535598
300
Verklein
Vergroot
Pagina terug
1/324
Pagina verder
290 QuickScan
TM
Lite QW2100
LED and Beeper Indications
INDICATION DESCRIPTION LED BEEPER
Power-up Beep
The reader is in the process of pow-
ering-up.
Reader beeps four times at highest
frequency and volume upon power-
up.
Good Read Beep
A label has been successfully
scanned by the reader.
LED behavior for this indica-
tion is configurable via the
feature “Good Read: When to
Indicate
The reader will beep once at current
frequency, volume, mono/bi-tonal
setting and duration upon a suc-
cessful label scan.
ROM Failure
There is an error in the reader's soft-
ware/programming
Flashes
Reader sounds one error beep at
highest volume.
Limited Scanning
Label Read
Indicates that a host connection is
not established when the USB inter-
face is enabled.
N/A
Reader 'chirps' six times at the
highest frequency and current vol-
ume.
Reader Active
Mode
The reader is active and ready to
scan.
The LED is lit steadily
a
a.
Except when in sleep mode or when a Good Read LED Duration other than 00 is selected
N/A
Reader
Disabled
The reader has been disabled by
the host.
The LED blinks continuously N/A
Green Spot is on
continuously
While in Stand Mode or Trigger
Object Sense mode the green spot
shall be on while in stand watch
state.
N/A N/A
Green Spot
a
flashes momen-
tarily
Upon successful read of a label, the
software shall turn the green spot on
for the time specified by the config-
ured value.
N/A N/A
Programming Mode - The following indications ONLY occur when the reader is in Programming Mode.
Label Programming
Mode Entry
A valid programming label has been
scanned.
LED blinks continuously
Reader sounds four low frequency
beeps.
Label Programming
Mode Rejection of
Label
A label has been rejected. N/A
Reader sounds three times at low-
est frequency & current volume.
Label Programming
Mode Acceptance
of Partial Label
In cases where multiple labels must
be scanned to program one feature,
this indication acknowledges each
portion as it is successfully
scanned.
N/A
Reader sounds one short beep at
highest frequency & current volume.
Label Programming
Mode Acceptance
of Programming
Configuration option(s) have been
successfully programmed via labels
and the reader has exited Program-
ming Mode.
N/A
Reader sounds one high frequency
beep and 4 low frequency beeps
followed by reset beeps.
Label Programming
Mode Cancel Item
Entry
Cancel label has been scanned. N/A
Reader sounds two times at low fre-
quency and current volume.
300

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Datalogic-QuickScan-Lite-QW2100

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Datalogic QuickScan Lite QW2100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Datalogic QuickScan Lite QW2100 in de taal/talen: Engels als bijlage per email.

De handleiding is 10,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Datalogic QuickScan Lite QW2100

Datalogic QuickScan Lite QW2100 Gebruiksaanwijzing - English - 24 pagina's

Datalogic QuickScan Lite QW2100 Gebruiksaanwijzing - English - 44 pagina's

Datalogic QuickScan Lite QW2100 Gebruiksaanwijzing - Türkiye - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info