566592
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
DKCD VI.51.T6.02 1/2003
Installation Instructions
Radiator thermostat RA 2000, universal model
Installation, temperature setting, limitation and blocking, theft protection
To remove the thermostat turn
the base counter-clockwise.
This will also reset the the
snap-action mechanism when
an audible "click" is heard.
Installation
Limiting and blocking the setting range
Theft protection
Remove the cover and install the theft
protection button, code 013G5245
without pushing it all the way in.
Once the thermostat is mounted on
the valve, push in the theft protection
device. The thermostat cannot be
removed.
Lower limit setting (min. setting)
Locking setting
Example: Required locked value = “3”
- Set thermostat at “3”
- Remove both pins from the the ther-
mostat.
- Place one pin under the diamond mark
and the othger pin under the triangle
mark.
Example: Required min. value = “2”
- Set thermostat at “2”
- Remove a pin from the bottom of the
thermostat with a screwdriver and
mount it under the triangle mark on
the knob (between setting positons
2 and 3).
Example: Required max. value = “4” -
Set thermostat at “4”
- Remove a pin from the bottom of the
thermostat with a screwdriver and
mount it under the diamond mark on
the knob (between setting positons 1
and 2).
Upper limit setting (max. setting)
To remove the theft protection use
screwdriver 013G1236 and screw into
the hole (1). Pulled out until the stop is
reached (2).
Temperature setting
The required room temperature is
obtained by turning the thermostat
knob. The numbers on the dial cor-
respond to the approximate tem-
peratures of the scale.
The temperatures indicated are
guidelines only. The actual room tem-
perature will depend on structural fac-
tors affecting the thermostats, location,
etc.
45 49 57 63 68 73 79 82°F
7 9,5 14 17 20 23 26 28°C
l 1 2 • • 3 • • 4 5 l
= Frost protection setting
The remote sensor must not
be in a drafty location or be
covered. Do not install above a
heat source. Attach the sensor
bracket to the desired location.
Pull out the required length of
capillary tube and secure to
the sensor as shown. Push the
sensor onto the base.
Remove the valve cover.
Check that the thermostat is
set at the factory setting of 5.
Push the thermostat firmly
onto the valve until an au-
dible "click" is heard.
Mounting thermostat with built-in sensor Mounting thermostat with remote sensor
1

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Danfoss-RA2000

Zoeken resetten

  • Beste ... voor de vervanging van een lekkende niet thermostatische regelknop wil ik een Danfoss RA-N knop plaatsen. Heb echter niet voldoende ruimte om de RA-N inclusief zogeheten insert te monteren / rond te draaien. Is de insert er uit te draaien en na montage weer terug te zetten ? Dan heb ik net voldoende montage-ruimte. Dank voor beantwoording. Gesteld op 26-1-2021 om 11:22

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Danfoss RA2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Danfoss RA2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Danfoss RA2000

Danfoss RA2000 Gebruiksaanwijzing - Nederlands - 12 pagina's

Danfoss RA2000 Gebruiksaanwijzing - Deutsch - 8 pagina's

Danfoss RA2000 Gebruiksaanwijzing - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info