654602
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
1
GP Programmers & Timeswitches
102, 103 and 106 Models, for time control of Domestic Central
Heating Systems.
Wallplate/
Terminal Block
Plug-in Module
INSTALLATION AND WIRING INSTRUCTIONS
SPECIFICATIONS
Power Supply : 220/240Vac, 50/Hz
Switch Action : 1 x SPST, Type 1B
Switch Rating : 220/240Vac, 50/60Hz, 6(2)A.
Timing Accuracy : ± 1 min./month
Enclosure Rating : IP20
Pollution Situation : Degree 2
Max. Ambient Temp. : 55°C
Designed to meet BS EN60730-2-7
Dimensions : 112mm wide, 135mm high, 69mm deep
Rated Impulse voltage : 2.5kV
Ball Pressure Test : 75°C
The unit must be installed by a competent electrician and the installation
should conform to I.E.E. Regulations. This unit should be wired via full
disconnect in accordance with BS EN60730-1, e.g. via a plug and unswitched
socket or double pole switch outlet with neon.
INSTALLATION INSTRUCTIONS
1. Loosen the fi xing screw in the base of the unit to release the grey
plastic Wiring Cover. Ensure the protective tape over the thumbwheel
remains in place.
2. Holding the unit clockface downwards, press fi rmly in the centre of
the wallplate and slide it from the module as shown.
3. Fix the Wallplate/Terminal Block to the wall with countersunk No.8
woodscrews or to a steel box to BS 4662. 1970 or a surface mounting
steel or moulded box having centres of 2
3
/
8
" (60.3mm).
4. Referring to the Wiring Diagrams overleaf, connect the unit as shown.
Ensure that terminals 3 and 6 are linked where required (Mains
Voltage applications) with insulated cable capable of carrying full load
current.
5. Ensure all dust and debris have been cleared away from the area, then
plug the module fi rmly into the wallplate ensuring that the hook at
the top of the wallplate engages with the slot at the back of the body.
Press the module down until it locates solidly.
6. Cut a cable aperture in the Wiring Cover if necessary; replace the Wiring
Cover, and tighten the fi xing screw.
7. Switch on Mains and test for correct operation as follows:
i) Remove protective tape from the pre-selector wheel.
ii) Remove the dial cover and rotate the clock dial two complete
revolutions to clear the mechanism.
ii) Check that all positions of the Selector Switch and Tappets operate
correctly. (See instructions in User Booklet.)
8. Replace the dial cover. Finally leave the USER INSTRUCTIONS with the
Householder.
9. If the unit is to be left turned off and is in a dusty atmosphere, protect
the pre-selector wheel by re-affi xing the protective tape.
IMPORTANT: Remove tape prior to putting unit into service.
Plug-in Replacement
Module
Selector Switch
Wallplate/Terminal Block
Pre-Selector Wheel
This product complies with the following EC Directives:
Electro-Magnetic Compatibility Directive.
(EMC) (2004/108/EC)
Low Voltage Directive.
(LVD) (2006/95/EC)
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Danfoss 106 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Danfoss 106 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info