639355
1
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
Follow these 10 steps to setup your telephone system
Connect the Exchange Lines
Analogue lines:
Start with the connector pair labelled ‘
Exchange
line 1
’.
Connect the pair to the exchange line, polarity
is not important.
ISDN lines (option):
Connect the grey ISDN socket to connectors
marked ‘
ISDN 1
’.
Connect lead from ISDN socket to the
exchange line.
Repeat for a second ISDN line using
connector marked ‘
ISDN 2
’.
Connect the Extensions
Wire each extension as follows:
The wires labelled ‘Signalling’ are only
required for the system keyphone, not for
ordinary telephones.
Remember to connect a keyphone to
extension 13 for system programming.
Ordinary telephones must be connected to
extensions 11,12, 21 and 23, circled on the
system label. These extensions are connected
directly to the exchange line in the event of a
power failure.
Switch on and check
Plug in the system, the green lamp on the
case will begin to flash.
The Terminals will begin to configure themselves
automatically, they will beep continuously while
this process takes place. The display will show
Terminal ID correct’ when the phone has
been correctly programmed. If not, then check the
following:
No dial tone ? – Try switching pins 3 and 4
around.
No ‘Terminal ID correct’ message after
entering code? - Try switching pins 2 and 5
around.
Finally, dial ‘80’ from any extension and
make sure all the other extensions ring.
Set the time & date
From extension 13 enter the time and date as
shown:
*9 7373 675 hh mm # 676 dd mm yy #
hh mm is the time using four digits, use two digits
for each number, ie: 9:30 am is 0930. ‘dd mm y’y is
the date.
ISDN Settings (option)
Check the settings of your ISDN line from
your telephone line provider. If it is in ‘point
to point’ mode, i.e.: no more than one device
can be connected to it, then enter the
following code at extension 13:
*8 260#
Finally, when extensions dial out from the
system, do you want to use ISDN lines or
analog lines first?
*8 200#
Choose analog lines first (default)
*8 201#
Choose ISDN lines first
The system is ready to go…
The system is now set to ring all extensions on
incoming calls. Extra features can be set overleaf.
Signalling
connector block.
Connect to the
terminals marked
‘Ter 1’ or ‘Ter 2’.
Extension
connector block
Connect to the
terminals marked
‘Extensions’
Pin 2
Pin 4
Pin 5
Pin 3
Extension
telephone
socket
not used
not used
1
1
1
2
2
2
4
4
4
3
3
3
Quick Start Guide
5
5
5
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DSS EUROCOM 612 PBX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DSS EUROCOM 612 PBX in de taal/talen: Engels als bijlage per email.

De handleiding is 0,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van DSS EUROCOM 612 PBX

DSS EUROCOM 612 PBX Snelstart handleiding - Nederlands - 2 pagina's

DSS EUROCOM 612 PBX Gebruiksaanwijzing en installatiehandleiding - Nederlands - 84 pagina's

DSS EUROCOM 612 PBX Gebruiksaanwijzing - English - 40 pagina's

DSS EUROCOM 612 PBX Gebruiksaanwijzing en installatiehandleiding - English - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info