65050
4
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Wiring
Power connections
Ground Terminal ( GND )
Remote terminal ( REM )
Use only four 30 ampere ATC
blade type fuses.
4
Power terminal ( +12V)
Connect the battery cable from the fuse holder to
the +12 Volt terminal on the amplifier.
Be sure to use a rubber grommet or a plastic
insulating tube where the cable passes the firewall
or other places when it can easily be jammed.
Use ty-wraps to secure to existing cables in the
engine compartment.
DLS FH2B
fuse holder
Connect to a good chassis ground. The ground
connection should be clean, unpainted metal to
provide a good electrical connection. Use a wire
brush, a scraper or a piece of an abrasive sheet to
clean the metal. Use a lock washer or two to secure
contact. Protect with silicon grease or by paint
applied afterwards.
Power
(Green)
Protect
(Red)
Power Light / Protect light
The power light (green ) comes on when
the amplifier is turned on.
The protect light ( red ) comes on
when the amplifier shuts down from
overheating, DC-offset or a short
circuit ( speaker failure)
Fuses on amplifier
For RCA cable signal input:
Set the input selector switch to position ”Low level”.
Connect the radio power antenna lead = remote
turn on/off from the car stereo to the amplifier
remote connection. This turns on the amplifier
whenever the car stereo is turned on.
You can either use the built in remote cable in the
RCA cable itself or use a separate cable.
Sometimes a small disturbance may enter the
amplifier coming from the remote voltage , through
the built in remote wire and into the RCA cable.
Thus we recommend to use a separate remote wire
and run the RCA lead separate from remote wire,
power cables and speaker cables.
Insert the cable directly into the amplifier terminal.
If there is no remote voltage available from the ste-
reo, you must connect to the ignition key through
the radio or any accessories fuse.
Set the ”High level auto
start” switch to position
OUT.
For High Level input:
Set the input selector switch to position ”High level”.
We recommend you to connect the remote wire as
described above. The amplifier will produce soft
on / soft off operation this way. If you use a remote
wire, set the switch ”High level auto start” to posi-
tion OUT.
In the case that there is no remote voltage available
from the car stereo, or you want to simplify the in-
stallation, the amplifier can be turned on/ turned
off by the high level input voltage. This is done
when the ”High level auto start” switch is set to IN
- position.
DLS
Connect with ring
terminal to
battery + terminal
Connect with ring
terminal to
chassis ground
Connect to head
unit remote start
terminal or power
antenna lead
Connect the fuse holder as close to the vehicle
battery + as possible, using 4 AWG = 21 mm
2
or
heavier cable. Use ring crimp terminal cable to
connect to battery +. Apply silicon grease to the
fuse to prevent corrosion.
Use a 100 Amp fuse for cable
4 AWG (21 mm
2
).
RA10 accepts 4 AWG
(21 mm
2
) in the power
terminal.
RA10
30 A
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DLS RA 10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DLS RA 10 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info