499500
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
2
DITEC S.P.A - IP1575 26/03/99 - BIX L / A
ITALIANO
1. Trasmettitore
Il trasmettitore è già pronto per il funzionamento. E’ dotato di un
codice individuale che lo distingue da qualsiasi altro trasmettitore.
I trasmettitori BIXLP2 e BIXLG4 (433.92 MHz) hanno i tasti di co-
lore blu. Il trasmettitore BIXAG4 (40.685 MHz) ha i tasti di colore
verde.
2. Ricevitore
I ricevitori sono previsti per essere inseriti direttamente nei quadri
elettrici DITEC. Solo i BIXLR2 e BIXAR2 possono essere usati
con le basi porta schede BIXA e BIXB. La presa seriale COM at-
tualmente non è utilizzata. Il ricevitore può ricevere i codici di tutti
i trasmettitori, ma attiverà l’uscita di comando solo se il codice
ricevuto é presente nella lista dei codici abilitati (max. 200 codici).
I ricevitori BIXLR1 e BIXLR2 sono dotati di antenna (filo rigido L=
173 mm). In alternativa è possibile collegare l’antenna accordata
BIXLA. I ricevitori BIXAR1 e BIXAR2 devono essere collegati
all’antenna accordata BIXAA. Per collegare l’antenna al ricevitore
usare cavo coassiale RG58 (max. 10 m).
L’antenna va posizionata il più in alto possibile, lontano da strutture
metalliche (nel lampeggiante LAMP e LAMPH è previsto un
morsetto per il collegamento dell’antenna).
3. ABILITAZIONE TRASMETTITORI
- Premere e rilasciare il pulsante PRG sul ricevitore
(alimentato), il led segnalazione SIG si accende.
- Effettuare una trasmissione premendo uno qualsi-
asi dei pulsanti di canale del trasmettitore. Il tra-
smettitore viene così abilitato. Durante questa fase
il led segnalazione SIG lampeggia. Quando il led
torna acceso fisso è possibile abilitare un nuovo
trasmettitore.
- Abilitare tutti i trasmettitori effettuando una trasmis-
sione come indicato sopra.
- L’uscita dalla procedura avviene in modo automa-
tico dopo 10 s dall’ultima trasmissione (il led SIG si
spegne).
4. SELEZIONE CANALI
Per attivare l’uscita 1 (OUT1) del ricevitore seleziona-
re con il ponticello J1 il canale desiderato. Per attivare
l’uscita 2 (OUT2) del ricevitore selezionare con il
ponticello J2 il canale desiderato. Canali preimpostati:
CH1 attiva OUT1, CH2 attiva OUT2. I led L1 e L2
indicano rispettivamente l’attivazione dell’uscita 1 e 2.
5. ABILITAZIONE TRASMETTITORI A DISTANZA
Per abilitare un nuovo trasmettitore senza intervenire
sul ricevitore è necessario disporre di un trasmettito-
re già abilitato ed effettuare le seguenti operazioni en-
tro il raggio d’azione del ricevitore (alimentato):
- Premere e rilasciare il pulsante PRG del trasmetti-
tore già abilitato (fig. 1). Attendere almeno 2 s per il
BIXAG4.
- Effettuare una trasmissione premendo uno dei pul-
santi di canale del trasmettitore da abilitare.
- Abilitare tutti gli eventuali nuovi trasmettitori premen-
do un pulsante di canale di ognuno di essi.
- L’uscita dalla procedura avviene in modo automati-
co dopo 10 s dall’ultima trasmissione.
6. Disabilitazione di tutti i trasmettitori
- Tenere premuto il pulsante PRG sul ricevitore, finché il led SIG
comincia a lampeggiare.
- Premere nuovamente il pulsante PRG entro 6 s per conferma-
re l’operazione. La conferma viene segnalata da un lampeggio
del led SIG a frequenza più elevata.
ENGLISH
1. Transmitter
The transmitter is ready to operate. It is provided with its own code
different from that of any other transmitter.
The BIXLP2 and BIXLG4 (433.92 MHz) transmitters feature blue-
coloured keys, while the BIXAG4 (40.685 MHz) transmitter has
green-coloured keys.
2. Receiver
Receivers are designed for directly inserting into DITEC electrical
boards. Only the BIXLR2 and BIXAR2 version can be used with
BIXA and BIXB card holders. The COM serial outlet is currently
not used.The receiver can receive the codes from all transmitters
but will only respond upon receiving a code which is included in its
file of authorised codes (max. 200 codes).
The receivers BIXLR1 and BIXLR2 are equipped with a 173 mm
long rigid antenna. Alternatively, it may be linked up to a BIXLA.
The BIXAR1 and BIXAR2 receivers must be linked up to the BIXAA
tuned antenna. Tuned antenna by means of an RG58 coaxial cable
with a maximum length of 10 metres.
The antenna must be mounted as high up as possible, away from
any metal structures (the LAMP and LAMPH flashing lights are
provided with a clamp for linking up of the antenna).
3. ENABLING THE TRANSMITTERS
- Press and release button PRG on the receiver (which
must be powered). A LED signalling light SIG will
come on.
- Transmit a signal by pressing one of the transmit-
ter channel buttons. During this operation the SIG
LED will be flashing. A new transmitter can be
enabled once the SIG LED has stopped flashing
and become fixed.
- Enable all the transmitters by transmitting a signal
as above mentioned.
- Exiting from the transmitter enabling function will
occur automatically 10 seconds after last transmis-
sion (the SIG LED will then go off).
4. SELECTING THE CHANNEL
Output 1 (OUT1) on the receiver is activated by the
selected channel via the jumper on J1 of the receiver.
Output 2 (OUT2)) on the receiver is activated by the
selected channel via the jumper on J2 of the receiver.
Default channels: CH1 actives OUT1, CH2 actives
OUT2. LEDs L1 and L2 signal that output 1 and 2,
respectively, have been activated.
5. REMOTE ENABLING OF THE TRANSMITTERS
A new transmitter can be remotely enabled without
acting directly on the receiver via an already ena-
bled transmitter within the receiving range of the pow-
ered receiver by proceeding as follows:
- Press and release the PRG button on the already
enabled transmitter (fig. 1). Wait at least 2 s for
BIXAG4.
- Transmit a signal by pressing one of the channel
buttons on the transmitter to be enabled.
- Enable any other transmitter proceeding as per 2.
above.
- Exiting from the transmitter enabling function will oc-
cur automatically 10 seconds after last transmission.
6. Disabling all transmitters
- Keep the PRG button on the receiver until the SIG LED starts
flashing.
- Within 6 seconds press the PRG button again to confirm the op-
eration. Confirmation will be signalled by the SIG LED flashing at
a faster rate.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

DITEC-BIXLP2-Remote

Zoeken resetten

  • garage deur opent af en toe langzaam. al 2 maal de veren strakker gezet ven de geleidings goten schoongemaakt maar helpt niet Gesteld op 20-3-2020 om 10:56

    Reageer op deze vraag Misbruik melden
  • ik heb 2 ditec poortopeners en soms willen de poorten gelijktijdig open gaan, wat is hier de oorzaak van Gesteld op 26-6-2015 om 14:40

    Reageer op deze vraag Misbruik melden
  • Hallo..

    Wij hebben een garagedeur ditec bixlp2.....
    Wij zouden daar graag de Nederlandse handleiding van hebben...
    Kunnen we die bij jullie opvragen...!!

    De deur gaat open en dicht maar vaak krijgt hij de kuren niets meer te willen....
    Er is al voor vele euro's aan gedaan...
    Wat raden jullie nu aan...
    Een andere moter,of een andere deur want de leverancier heeft ook geen oplossing...
    Hij krijgt hem niet gemaakt.....lekkerrrrrrrrr......

    Steeds weer opnieuw...andere batterijen...zelf al andere besturingskastjes....het schiet niet op.....
    Lekker al die kosten en nog niets opgelost !!!!!!!

    Met vriendelijke groet hopen we van jullie een antwoord te krijgen....
    Alvast dank u wel namens ons.....

    Mevr van Heumen...
    Waalwijk.... Gesteld op 13-10-2013 om 13:00

    Reageer op deze vraag Misbruik melden
    • Beste mevrouw van Heumen,
      Helaas kan ik uw probleem niet oplossen maar ik wilde u wel laten weten, dat wanneer u de afstandsbediening Ditec BIXLP2 weg gaat doen, ik deze graag van u wil kopen.
      e.majeur@ziggo.nl.
      Groeten
      van
      Ellen Majeur
      Geantwoord op 6-2-2014 om 13:09

      Waardeer dit antwoord Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DITEC BIXLP2 Remote bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DITEC BIXLP2 Remote in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van DITEC BIXLP2 Remote

DITEC BIXLP2 Remote Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info