728116
3
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
Ports 1x to 4x These eight ports can be used to connect
end-stations to the router using straight-through cables.
ISDN This socket is used to connect the ISDN line to
either an NT-1 or directly to the ISDN wall jack, depend-
ing on the type of service delivered by your phone
company.
Installation and Initial Configuration
Step 1 - Connecting an ISDN Line to
the Router
Your phone company will provide an S/T interface into
your home or office. Plug the ISDN line from the router
directly into the ISDN wall socket provided by your phone
company.
Step 2 - Connecting Ethernet Cables
to the Router
Your DI-304 has four ports for connecting 100BASE-TX
Fast Ethernet devices to form a LAN. The jacks for ports 1
through 4 are wired to let you connect network end nodes
(computers, servers, bridges, other routers, etc.) using stan-
dard straight-through EIA (Electronic Industries
Association) Category 5 or higher twisted-pair cables. The
jack for the sixth port is labeled Uplink and is wired to let
you connect to another 10Mbps or 10/100Mbps Ethernet or
hub or Switch using a straight-through cable, or an end
node using a cross-wired cable.
Please refer to the following chart when deciding on the
type of cable necessary for a given connection:
DEVICE PORT
USED
DEVICE
BEING
CONNECTED
PORT
TYPE
CABLE
TO USE
Hub or
Normal
Crossover
(X)
Normal
Switch
Uplink
Straight-
Through
(||)
Router Server (or PC)
Straight-
Through
(||)
Hub or
Normal
Straight-
Through
(||)
Uplink
Switch
Uplink
Crossover
(X)
Server (or PC)
Crossover
(X)
The figure below shows how to make an Ethernet connec-
tion between the router and a network end node.
RJ-45 connector
RJ-45 connecto
r
Important Notes on Ethernet Connec-
tions
Observe the following rules when connecting devices with
twisted-pair Ethernet cables:
For both end-node and uplink connections, use only EIA
Category 5 or higher-grade twisted-pair data cables with
RJ-45 plugs. In almost all cases, only standard straight-
through cables are needed.
Make sure no cable is more than 100 meters (328 feet)
long.
When uplinking two hubs together with a straight-
through cable, use an uplink-type jack at one end, and an
end-node-type jack at the other.
If uplinking more than two hubs together, observe the 5-
4-3 rule: no signal, in order to go from one end node to
another, must ever pass through more than five twisted-
pair cables, four repeaters (that is, hubs), and three up-
link cables. This is the maximum signal path in twisted-
pair Ethernet. Also be sure never to allow a signal loop
to form.
10BASE-T cable
(straight-through wires)
Note that you can connect an end node through the Up-
link jack, but to do so you must use a cross-wired cable
or cable converter.
Step 3 - Powering Up Devices for Ini-
tial Configuration
Plug in the included 18V AC, 1000 mA power adapter into
the power jack on the routers rear panel.
You should have now connected the ISDN phone line, one
or more Ethernet cables, and the power adapter.
3
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw D-Link DI-304 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van D-Link DI-304 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van D-Link DI-304

D-Link DI-304 Gebruiksaanwijzing - English - 96 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info