534701
30
Verklein
Vergroot
Pagina terug
1/31
Pagina verder
Your Print Pad may become un-leveled when transporting your Cube. If this occurs, please follow these instructions to
level your Print Pad for optimum creation experience. The Print Pad pad can be leveled with the two adjusting bolts located
underneath the front and back of the pad.
1. Press the power button on the Cube control panel.
2. Ensure Print Pad is properly installed on print plate.
3. Finger tap SETUP on the touchscreen and scroll through the menu until LEVEL
PLATE appears. Press LEVEL PLATE; the Print Pad will move up to Print Jet tip.
4. Using the Up arrow, raise the Print Pad to the Print Jet tip until the tip is near the
Print Pad but not touching it.
5. Touch the “clockwise” and “counter-clockwise” buttons to automatically move the
Print Jet around the four corners of the Print Pad. During each movement along the
sides of the Print Pad, observe any gaps between the pad and the Print Jet. If there
are gaps on one side of Print Pad and the Print Jet tip is barely touching the Print
Pad on the other side, the Print Pad pad is not level.
NOTE: Please refer to the FRONT TO BACK or SIDE TO SIDE instructions on how
to turn the adjusting knob bolts to level the pad properly.
6. Place a standard sheet of paper between the Print Jet tip and the Print Pad where
the adjustment needs to be made. If the paper cannot slide between the Print Jet tip
and Print Pad, tap the down arrow key on touchscreen.
ROLL SIDE TO SIDE
If the gap between the Print Pad and Print Jet tip is at the right or left side, adjust the pad
using the rear adjusting knob bolt (B). If the gap is too low, the pad is too low and will
need to be moved up.
1. If the pad needs to be moved up, turn the front adjusting knob bolt (A) clockwise to
loosen and then turn the rear adjusting knob bolt (B) clockwise. To move the pad
down, turn the rear adjusting knob bolt (B) counterclockwise.
2. While adjusting, slide the paper between the Print Jet tip and Print Pad where the
adjustment was needed; the paper should slide back and forth with no resistance. If
resistance is felt, the pad is too high. Please repeat the adjustment.
3. Once adjustments are made, tighten the adjusting knob bolts.
TILT FRONT TO BACK
If the gap between the Print Pad and Print Jet tip is at the front or back of pad, adjust the pad using the rear adjusting knob
bolt (B). If the gap appears on the side, the pad is too low and will need to be moved up.
1. If the pad needs to be moved up, turn the front adjusting knob bolt (A) clockwise to loosen and then turn the back
adjusting knob bolt (B) clockwise. To move the pad down, turn the rear adjusting knob bolt (B) counterclockwise.
2. While adjusting, slide the paper between the Print Jet tip and Print Pad where the adjustment was needed; the paper
should slide back and forth with no resistance. If resistance is felt, the pad is too high. Please repeat the adjustment.
3. Once adjustments are made, tighten the adjusting knob bolts.
NOTE: After the print jet is adjusted, you will need to reset the print jet gap; please refer to Section 16: Setting Print
Jet Gap.
A B
29
24 PRINT PAD LEVELING INSTRUCTIONS
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cubify Cube bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cubify Cube in de taal/talen: Engels als bijlage per email.

De handleiding is 3,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info