648459
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
EN • 3
BATTERY TYPES AND SETTINGS
M300 can easily be set for different types of batteries or conditions. The following recommendations should, however, only be seen as
guidelines. Please consult the battery manufacturer for further instructions.
Settings are made by pressing the “MODE-button “ and stepping forward one press at a time until the required mode is reached, the
button is then released. After about 2 seconds the charger activates the selected mode. The selected mode is saved in a memory in
the charger and remains there even if the charger is disconnected from battery and mains.
NORMAL
NORMAL - Normal setting for wet batteries, maintenance free and for most Gel batteries. Some Gel batteries
prefer a slightly lower charging voltage. Please consult the battery manufacturer when in doubt.
NIGHT
NIGHT – This mode is equal to NORMAL, but with reduced current. The built-in fan is disabled and the unit is
almost silent. The Unit returns automatically to NORMAL after 8 hours. To ensure that the charger restarts in
NIGHT mode in the event of a power failure the setting is stored in a memory. The indication shows “NIGHT
even if the charger has returned to NORMAL mode to remind that the charger will start in NIGHT mode next time.
RECOND
RECOND - This mode is used to recover deep discharged ooded batteries where you could expect a stratied
acid (high acid weight in the bottom, low on top). Check with battery manufacturer when in doubt.
Use this mode with care, because the high voltage will cause some water loss. 16V is normally no problem
for electronics in 12V system. Consult your supplier when in doubt. Life of light bulbs will be reduced at higher
voltage. Try to disconnect light from the battery during this phase. Maximum effect and minimum risk for
electronics is achieved by charging a disconnected battery.
CHARGING PHASES
M300 charges and analyses in eight fully automatic steps. M300 has three different operating modes, see Battery Types and Settings.
The battery charger has an 8-step fully automatic charging cycle:
Desulphation
Desulphation with pulses recovers sulphated batteries. Indicates with lamp 1.
Soft start (Lamp 1)
Start mode for the charging cycle. The start phase continues until the battery’s terminal voltage has risen above the set limit, at which
point the charger switches to bulk charging. If the terminal voltage has not passed the voltage limit within the time limit, the charger
switches to fault mode (lamp 0) and discontinues the charging. If so, the battery is faulty or its capacity is too large.
Bulk (Lamp 2)
Main charge when 80% of charging takes place. The charger delivers maximum current until the terminal voltage has risen to the set
level. Bulk has a maximum time, at which point the charger automatically switches to Absorption.
Absorption (Lamp 3)
Complete charge up to virtually 100%. The terminal voltage is maintained at the set level. During this phase the current tapers
successively. Once the current has tapered to the set limit, this phase switches to being timed. If the total time for Absorption exceeds
the time limit the charger automatically switches to maintenance.
Analysis (Lamp 3)
Testing self-discharge. If self-discharge is too high, charging is discontinued and fault mode is indicated.
Maintenance charging - Float (Lamp 4)
Charging at constant voltage.
Maintenance charging - Pulse (Lamp 4)
Charging varies between 95% and 100% state of charge. The battery receives a pulse when the voltage drops and keeps the battery
in perfect condition when it is not in use. The charger can be connected for months at a time. The charger continuously measures the
terminal voltage to determine whether a charging pulse should be initiated. If the battery is loaded and/or the battery’s terminal voltage
drops the charger starts a charging pulse until the terminal voltage reaches the set level. The charging pulse is then discontinued and
the cycle is repeated innitely. If the terminal voltage drops below a lower limit, the charger automatically goes back to the beginning
of the charging curve.
Recond (Lamp 5)
This mode is used to recover deeply discharged ooded batteries. Recondition of deep discharged batteries. The voltage increases
with reduced current for a limited time period. The higher voltage starts some gassing and mixing of the acid, which is benecial for
both battery capacity and expected life. Note that the battery could emit explosive gas during Recond. Recond is performed between
Analysis and Maintenance.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ctek M300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ctek M300 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ctek M300

Ctek M300 Gebruiksaanwijzing - Nederlands - 8 pagina's

Ctek M300 Gebruiksaanwijzing - Deutsch - 8 pagina's

Ctek M300 Gebruiksaanwijzing - Français - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info