167580
24
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
Speaker- and Audio-Connections: MXB480 / MXB4125
3-Channel Stereo-/Subwoofer-Mode
Connect the RCA INPUTS of the amplifier to the head unit line outputs with appropriate
RCA cables. If your head unit is not equipped with pre-amplifier RCA line outputs you
can use the optional HI INPUTS (Highlevel Inputs). Connect therefore the speaker outputs of your
head unit with the enclosed cable plug. Check the Wiring Diagram below.
Connect the frontspeakers with the speaker ouputs (SPEAKERS/ + CH1 -, + CH2 -) and the subwoofer
with the speaker outputs (+ BRIDGED - from CH3/4) of the amplifier by using appropriate cables.
Ensure that the total speaker impedance load is not lower than 2 Ohms channel on channel 1/2 and
4 Ohms on subwoofer channel 3/4.
Too low speaker loads result in too high heat development and may cause the amplifier run into
protection.
INPUT SELECT - switch
• Select here the 4CH-Position.
FILTER - selector channel 1/2
If larger speakers (> Ø20 cm) are used, the FLAT position is recommended. A fullrange signal will be provided to the speakers.
For all smaller speakers (Ø8.7cm - Ø16cm) the Position HIGH PASS is recommended, thereby the lower frequencies will eliminated
in the audiosignal. Set the cut-off frequency between 60Hz - 150Hz, depending of the size of the installed speakers.
The cut-off frequency is adjustable with the HIGH PASS controller.
• In this configuration example the LOW PASS - controller is not used.
INPUT LEVEL - controller channel 1/2
• Turn the INPUT LEVEL controller on the amplifier to 4V position.
• Turn the head unit volume controller to about 80-90% of its full setting.
• Turn the INPUT LEVEL controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL controller slightly until you can hear clean sound.
REFERENCE NOTE: If this controller is cranked up too high, the amplifier produce distortions, which may cause a
“creeping death” of the amplifier (or the speakers). Usually this is called “Clipping”.
BASS BOOST - controller channel 1/2
• Turn the BASS BOOST controller into “0dB” - position.
FILTER - selector subwoofer channel 3/4
In the Subwoofer-Mode mono bridged the FILTER - select must be in position LOW PASS, thereby the higher frequencies will be
eliminated in the audiosignal. Set the cut-off frequency between 60Hz - 100Hz, depending on the size of the installed subwoofer
The cut-off frequency is adjustable with the LOW PASS - controller. In this configuration the HIGH PASS - controller is not used.
INPUT LEVEL - controller subwoofer channel 3/4
• Turn the INPUT LEVEL - controller on the amplifier to 5V position.
• Turn the head unit volume controller to about 80-90% of its full setting.
• Turn the INPUT LEVEL - controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL - controller slightly until you can hear clean sound.
REFERENCE NOTE: If this controller is cranked up too high, the amplifier produce distortions, which may cause a
“creeping death” of the amplifier (or the speakers). Usually this is called “Clipping”.
BASS BOOST - controller subwoofer channel 3/4
• The BASS BOOST - controller adjusts the bass boost from 0db to +12dB.Caution! Please use the Bass Boost carefully.
REFERENCE NOTE: Ensure always correct polarity for all connections.
Don’t connect any speaker cables to the vehicle’s ground.
24
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Crunch mxb 280 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Crunch mxb 280 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info