498254
26
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
4 Channel Amplifier - Applications
MXB-480/MXB-4100/MXB-4125/MXB-4175
One 4 Channel Amplifier in Stereo Mode (Front-/Rear- Speakers) with
One 2 Channel Amplifier in Mono/Subwoofer Mode (Bass Amplifier)
Interconnect cable checklist:
•Connect the INPUT of the 4 Channel Amplifier to the head unit line outputs with good quality
RCA to RCA cables.
• Connect the OUTPUT of the 4 Channel Amplifier with the LINE LEVEL INPUT of the
designated Bass Amplifier (2 Channel Amplifier) with a further RCA cable.
• Connect the Front-/Rear Speakers with the terminal blocks (SPEAKERS / + CH1 -, + CH2 -,
+ CH3 - and + CH4 -) of the 4 Channel Amplifier.
• Connect the Subwoofer with the terminal block (SPEAKERS / + BRIDGED -) of the
designated Bass Amplifier (2 Channel Amplifier).
•The minimum final speaker impedance must not be below 2 Ohms for the 4 Channel
Amplifier, the total impedance of the Subwoofer(s) must not be below 4 Ohms. Too low
speaker loads result in too high heat dissipation and may cause the amplifier run into
protection.
• If you use more than one speaker (Subwoofer), make sure that both are connected in
phase. Incorrect polarity of the speakers results in total loss of bass response.
Caution
Be careful not to connect speaker (-) to the ground or vehicle chassis.
Control settings of the 4 Channel Amplifier:
FILTER SELECT (CH1/2 & CH3/4)
If larger than 20 cm speakers are used, the FLAT position is recommended.
For all smaller speakers (Ø8.7cm - Ø16cm) the Highpass-Position (HIGH PASS) is recommended, which eliminates the
lowest frequencies and protects the speakers from damage. Set the crossover-frequency between 60Hz - 150Hz, depending
of the size of the installed speakers. The Highpass adjustment can be done with the HIGH PASS control.
• In this configuration example the LOW PASS control is not used.
INPUT LEVEL (CH1/2 & CH3/4)
• Turn the INPUT LEVEL controls on the amplifier to 4V position.
• Turn the head unit volume control to about 80-90% of its full setting.
• Turn the INPUT LEVEL controls clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL controls slightly until you can hear clean sound.
BASS BOOST (CH1/2 & CH3/4)
• Turn the BASS BOOST control into “0dB” - position.
INPUT SELECT
• The INPUT SELECT - switch must be in “4” - position.
Control settings of the Bass Amplifier (2 Channel Amplifier):
FILTER SELECT
In 1 Channel/Mono-Mode select the Lowpass-Position (LOW PASS), which eliminates the higher frequencies. The
recommended crossover frequency ranges between 60 - 100Hz, depending on the size and response of the Subwoofer. The
Lowpass adjustment can be done with the LOW PASS control. In this configuration example the HIGH PASS control is not
used.
INPUT LEVEL
see descriptions for 4 Channel Amplifier above
BASS BOOST
• The BASS BOOST - Control increases the bass level at 45 Hz max. +12dB.
Caution! Please use the Bass-Boost carefully. The additional boost may result in clipping or overload.
25
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Crunch MXB2125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Crunch MXB2125 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info