652347
35
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
35
Inspect for correct installation in accordance with the following checklist:
Do the details on the rating plates for heating and control voltage match the relevant network
voltage?
Is/are the CP2-chip(s) correctly used?
Are the voltage supplies (heating and control voltage) correctly fused?
Is the service switch Q installed in the supply line for to the heating and control voltage?
Are all components correctly connected according to the connection diagram?
Are all connecting cables fastened?
Are the connecting cables free of tension (passed through cable boltings?)
Are the units configured correctly?
5.5.2 Inserting CP2-chip (models H5...H8, F... and G... only)
5.5.3 Inspecting the electrical installation
All important operating parameters such as the maximum steam capacity, the heating voltage and the
number of base units are permanently stored on the CP2-chip.
Before you start the electrical installation, check whether the CP2-chip is installed. If it is not, check
whether the type designation on the CP2-chip supplied corresponds with the type designation
on the data plate of the units). If the designations match, place the CP2-chip in the control print with
the data plate to the front (see figure above). Then cover the data plate on the right side of the unit with
the data plate supplied (self-adhesive).
If the type designation on the CP2-chip and the data plate do not match, the CP2-chip must not be
installed. If this is the case, contact your Condair supplier.
Note for multiple units: Only use CP2-chips with the same serial number in the basic unit of a model
group. To identify the individual basic units a letter (A, B, C, etc.) follows the serial number. Install CP2-
chip marked A into the Master unit equipped with display or module M.. respectively (in con-
figurations with units of different sizes the Master unit is always a large unit). Install the other CP2-
chips into the respective Slave units (Important: the model designation of the CP2-chip must
correspond to the model designation on the data plate of the respective unit).
Important! CP2-chips for individual units cannot be used in multiple units and CP2-chips for multiple
units cannot be used in individual units.
1
2
3
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Condair CP2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Condair CP2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info