634448
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
L
Never try to fo
rce the splitting of the log by maintaining
the pressure for several seconds. This can lead to damage to
the machine.
Reposition the log on the main frame and repeat the splitting
process, or put the log to one side.
How to release a jammed log?
1. Loos
e the operating lever as well as the operating
pushbutton that the log ram can go back.
1. Place a triangular wooden chock under the log, then move
the log ram forward so that it pushes the chock under the
jammed log.
2. If the log is not released, keep repeating this procedure,
using larger chocks, until the log is released.
Never use a hammer to release a jammed log, and keep
your hands away from the log.
Do not enlist the aid of a second person - this is a one-man
job.
Do not try to release the log by using a hammer, since this
may break the motor block.
Finishing work:
Wait for the log ram has go back to its initial
starting / basic position.
Then remove the plug from the power socket.
Close the bleed screw. Fig. 5
Follow the care and maintenance instructions.
C
C
a
a
r
r
e
e
a
a
n
n
d
d
m
m
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
Remo
ve the plug from the power socket before
starting any maintenance or cleaning work.
Wear protecti
ve gloves in order to avoid injury to the
hands.
L
Observ
e the following in order to keep the log splitter in
good working order:
Clean the machine thoroughly after you have finished
usi
ng it.
Remove any resin remains on the machine.
Oil the piston rod (Fig. 1) regularly with an
environmentally friendly spray oil.
Check the oil level and change the oil as necessary.
Sharpening the splitting wedge
After ex
tended periods of use, or if the splitting performance is
reduced, sharpen the splitting wedge with a file (and remove
any burrs). Fig. 8
Fig. 8
How do I check the oil level?
1. The log r
am must be in its starting position.
2. Stand the log splitter on end, with the filler opening at the
top. Fig
9
A second pe
rson will be required to up-end and
hold the log splitter.
3. Unscrew the dipstick – Fig. 10. Do not drop or lose the oil
seal when removing the dipsti
ck.
4. Clean the dipstick and the oil seal.
5. Replace the dipstick fully into the oil reservoir.
6. Now remove the dipstick again, and read off the oil level.
If the oil
level is between the two marking on the
dipstick, there is sufficient oil in the reservoir.
If the oi
l level is below the lower marking, more oil
should be added with the aid of a clean funnel.
lower marking upper marking
7. Check th
e oil seal and replace it if it is damaged in any
way.
8. Repl
ace the dipstick and screw it firmly into place.
Caution! Do not tighten the screw too tightly, since this may
damage the oil seal or the thread in the cylinder cover.
Oil seal
Sharpen wedge
6
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cobra LS520H bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cobra LS520H in de taal/talen: Engels als bijlage per email.

De handleiding is 17,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info