538258
7
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
Operation
Operation
98
12V DC appliances
The power pack can operate one 12V DC auto, RV, marine, or other portable DC
appliance that draws 10 amps or less from its DC socket. The combined load
must not exceed 120 W, The less combined wattage used, the longer the power
pack will operate before recharging is required.
Operating DC appliances:
1. Check battery status to ensure the battery is fully charged.
2. Open the DC socket.
3. Plug the DC appliance into the DC socket.
4. Turn the DC appliance ON.
5. Recharge the power pack immediately after use.
USB Devices
The power pack can charge or power one USB-chargeable device through its
USB port. Compatible devices include most MP3 players, PDAs, digital cameras,
and camcorders that have internal batteries which can be charged via the USB
port of a desktop/laptop computer.
USB-chargeable devices usually include a special USB cable (not supplied) that
attaches one end to the USB port and the other end to the device.
Jump starting a vehicles engine
You can use the power pack to jump start a vehicle (or boat engine) that has a
12V starting battery using the jump start cables supplied with the unit.
WARNING: Fire Hazard
A reverse polarity connection may cause damage to the unit and/or create a
sparking/explosion hazard. Never allow cables red and black clamps to touch
each other or another common metal conductor. The connection of the cables
to the vehicles battery terminals must be positive to positive (red clamp to
battery “+”) and negative to negative (black clamp to battery “-“ or vehicle
chassis).
NOTE: Carefully follow these instructions for jump starting your vehicle as they
may be different from the instructions supplied with other jump start products
or cables.
To jump start a vehicle:
1. Turn off the vehicle and all accessories.
2. Place the unit on a flat and stable surface near the battery which need to be
started. Ensure that the unit’s jump start power switch is OFF.
3. Connect the red positive (+) clamp of the cables to the positive (+)
terminal of the engine battery.
4. Connect the black negative (-) clamp of the cables to the engine block,
cylinder head, or other stationary heavy metal part of the motor. If the red
“Reverse Polarity” LED illuminates, then reverse polarity has been detected.
Correct polarity must be established before proceeding. Disconnect the
jump starting clamps from the vehicles battery and repeat steps (3) and (4).
5. Switch on the jump start power switch. Before starting the engine, make
sure the jumpstarter pack and the cables are clear of the metal parts and
other moving things.
6. Crank the engine for 5 seconds or until it starts, whichever is first.
WARNING: Fire hazard
Do not try to start the engine for more than 5 seconds. The jump start
feature is designed for short term operation only. Operating the jump
starting feature for more than 5 seconds may cause damage to the unit.
Allow the unit to cool down for at least 3 minutes after each start attempt.
7. Switch off the jump start power switch.
8. Remove the red positive (+) clamp and then the black negative (-) clamp.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cobra CJS 50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cobra CJS 50 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info