703410
3
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
EN Instructions
Customer Service / Importer:
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
+49 38851 314650 *)
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
All rights reserved.
Assembly
1. Insert the rod with the drip protec-
tion into the recess which is provid-
ed for it on the main device.
2. Fit the Y tube (1) on the rod with the
drip protection.
3. Insert the two rods (3) into the Y
tube.
4. Attach the nylon balloon (2):
draw it over the two rods
.
draw the elastic over the mounting
ange on the main device.
The device is disassembled in the re-
verse order.
Use
1. If you have not yet done so, attach
the nylon balloon (2) (see the “As-
sembly” chapter).
The nylon balloon should sit im-
mediately below the mounting
ange so that it can fully in ate.
2. Pull the garment which is to be pressed over the nylon balloon
and do up the zip or buttons if necessary. Make sure that
the legs of the nylon balloon t properly into the legs of the
trousers and are not twisted or scrunched up,
all buttons on the garment (including the legs) are done up.
3. Spread the clamps (supplied with the main device) along the
bottom of the garment (at the front and back in each case on
the outsides) so that it is weighed down and will not go out of
shape when the nylon balloon is in ated.
4. Operate the device as described in the instructions for use of
the main device.
5. Once the nylon balloon has in ated, straighten out the garment
and smooth it down again.
6. Remove the garment from the nylon balloon after the comple-
tion of the drying/pressing process.
7. Switch off the main device, unplug it and allow it to cool.
Tips
• The drying/pressing process takes around 10 minutes for
spun-dried trousers. However, the length of time can vary
depending on the material and thickness of the material. We
recommend that you start with a shorter time and extend it if
necessary.
In the case of trousers with a very small waist it may not be
possible to pull them over the attachment when it has already
been tted. In this case you proceed as follows:
push the nylon balloon (2) upwards slightly, to enable access
to the rods (3),
remove one of the two rods from the Y tube once more (1),
draw the trousers over the two rods,
now replace the rods in the Y tube and
draw the nylon balloon over the mounting ange on the main
device again.
Wide-apart buttons may result in the button strip crimping
slightly during pressing. Here it is advisable to smooth down
the button strip again by hand immediately after the pressing
process.
After the drying/pressing process any creases need to be
ironed out using a normal iron.
Cleaning and Storage
Before commencing the cleaning, note the safety instruc-
tions in the “Safety Instructions” chapter and the operating
instructions for the main device!
Clean the device if necessary with a slightly damp cloth and
a little mild detergent if required. Then wipe down fully with a
dry cloth.
Allow all parts to dry completely before you put them away.
Store the article in a clean, dry place that is protected from
sunlight and is not accessible to children and animals.
Disposal
Dispose of the packaging material in an environmentally
friendly manner and take it to a recycling centre. Dispose
of the article in an environmentally friendly manner as well.
More information is available from your local authorities.
Z 00513 M DS V1 0418
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cleanmaxx Z00513 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cleanmaxx Z00513 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info