455925
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
5
CLIPCLIP
SP200
ON
OFF
FRONT PANEL
1. POWER SWITCH
2. POWER LED INDICATORS
3. LIMIT LED INDICATORS
To turn the unit ON or OFF, press the Left or Right portion of
this button. Before turning on the amplifier, check all connections
and turn down the level controls.A momentary muting is normal
when turning the amplifier on or off.
(Caution: Always turn on your power amplifier last, after all your
other connected equipment, and always turn off your power
amplifier before your other connected equipment.)
These LEDs illuminate when the power is turned "ON".
These LEDs illuminate if any section of the power amplifier's
output are within 3dB of clipping. Occasional blinking of the LEDs
are acceptable, but if they remain on more than intermittently you
should turn down either the power amplifier s level controls or
reduce the output level of the preceding component to avoid
audible distortion.
These LEDs illuminate to confirm the presence of an input signal
greater than 100 mV at that channel of the amplifier
These LEDs illuminate if the power amplifier s output connection
is shorted or the load impedance is too low. When either of these
LEDs is lit up, turn OFF the power and check the output's connec-
tion to verify that it is correct, then turn ON the power again.
These control the level of signal coming into each channel. The
actual voltage gain of the amplifier is shown in dB. Turn these
controls counterclockwise if the peak LEDs illuminate steadily
(indicating too strong an input signal).
4. SIGNAL LED INDICATORS
5. PROTECT LED INDICATORS
6. LEVEL CONTROLS
61 6
4
2
3
5
10. INPUT CONNECTORS
11.L/R CHANNELOUTPUT CONNECTORS
12.BUILTIU LIMITER ON/OFF SELECTOR
13. FANS
Connect your input signal to these balanced 1/4"TRS input jacks.
Connect to your speaker box.
The fan speed is varied continuously and automatically to maintain
the proper internal operating temperature.
8
9
7
13
11
BACK PANEL
7. POWER CONNECTOR
8. FUSES
9. AC VOLTAGE SELECTOR SWITCH
The cord connector is used to connect the AC power source to
your power amplifier.
Fuse holders for (AC115V:T6.3A/250V AC230V:T3.15A/250V)
fuses. If these fuses continuously. blow, shut off the unit and have
it serviced by qualified service personnel.
Before plugging in the power cord, check to see that the unit is set
for the proper voltage for your area:~115V(60Hz)or ~230V(50Hz).
(CAUTION: DO NOT REMOVE THE CENTER GROUNDING
PIN.)
10
12
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Citronic SP Series bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Citronic SP Series in de taal/talen: Engels als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info