455923
4
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
With CH1 and CH2 level controls turned fully down, switch on the power to the amplifier. This product has a “soft-
start” function which makes some checks before engaging power to the amplifiers, which may take a few seconds.
With mixer (or other signal source) levels turned down, gradually increase the amplifier’s CH1 and CH2 level
controls to the required level (normally full) and then gradually increase the signal level from the mixer until sound
can be heard through the speakers and then up to the required level.
During use, the LED indicators will show if a signal is present, if half output is being produced and if the output is
reaching clip level. If the red CLIP LEDs illuminate more than very briefly, reduce the volume until they hardly light
up at all.
If the internal protection circuitry detects a fault in the speakers or amp, the amplifier will enter Protect Mode and a
“PM” LED will illuminate on the front panel to show this. Switch the amplifier off and check the entire system
(including leads) before powering up again. If still in Protect Mode, seek advice from qualified service personnel.
Before powering down, turn CH1 and CH2 level controls fully down to avoid loud noises when switching off.
SPECIFICATIONS
PL3200
PL3800
Power supply
Output: RMS @ 4
2 x 1600W
2 x 1900W
Output: RMS @ 8
2 x 915W
2 x 1100W
Bridge power: RMS @ 8
3200W
3800W
Input impedance
Output circuit architecture
Frequency response
S/N ratio
>111dB
>112dB
THD
Circuit protection
Dimensions
Weight
Troubleshooting
No power light on front panel switch
Ensure IEC is connected to mains and mains lead is in good condition
Ensure mains outlet is switched on
Power light is on but no other LEDs and not
output
Check input signal and connection leads
Ensure CH1 and CH2 level controls are not turned fully down
Power light and Signal LEDs are lit but no
output
Check speaker cabinets are not blown and are in good working order
Check speaker leads are in good condition and connected properly
PM (Protect Mode) LED is lit and there is no
output
Switch off and disconnect from mains
Check speakers are in good working order and not shorted out (using a
multi-tester)
After checking all connected items, power up again
If still in Protect Mode, switch off again and refer to qualified service
personnel
Output is very distorted and “CLIP” LEDs are
lighting
Check speaker impedance is not below rated Ohms
Turn down Input level from audio source
Switch GAIN at rear to a lower level
Turn down CH1 and CH2 level controls
Output is working but at very low level
Ensure input source is at line level
Increase input level from audio source
Turn up CH1 and CH2 level controls
Switch GAIN at rear to a higher level
Note: for further troubleshooting, refer equipment to qualified service personnel for testing
© Citronic 2011
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Citronic PL3800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Citronic PL3800 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info