455918
4
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Operation
Begin with all frequency sliders and the GAIN controls in the centre position (no boost or cut) at 0dB.
Switch the “IN/OUT” button to IN and the respective LED will light.
Adjust each frequency in turn to acquire the best response and reduce any problem frequencies.
Bear in mind that many loudspeakers cannot reproduce frequencies down as far as 20Hz and that the energy from
the amplifier at these low frequencies is wasted as heat in the speaker coil. Therefore, the “LOW CUT” may be
preferred to be on in sound reinforcement scenarios.
Also, with live PA situations, the crossover point between subs and mid-top cabs can generate phase problems
which may be alleviated by reducing frequencies around this point.
Extremely high frequencies are often not feasible for live sound systems, due to the limitations of microphones and
loudspeakers (and most people’s ears) and 20kHz may be reduced to save wasted amplifier energy at these high
frequencies.
For whichever particular application, experimentation and practice will eventually give the best results from your
equalizer.
SPECIFICATIONS
Power supply
115/230Vac 50/60Hz - selectable (IEC)
Frequency response
20Hz - 20kHz
Input impedance : Balanced
40kohms
Input impedance : Unbalanced
20kohms
Output impedance : Bal/Unbal
330ohms
Channel separation
>50dB
Signal to noise ratio
>102dB
THD
0.01%
Dimensions
44 x 482 x 138mm
Weight
2.0kg
Power supply
115/230Vac 50/60Hz - selectable (IEC)
Frequency response
20Hz - 20kHz
Input impedance : Balanced
40kohms
TROUBLESHOOTING
Ensure mains voltage is correct and connected properly
Ensure front panel power switch and mains outlet switch are on
Check XLR and/or jack leads are OK and connected properly
Check that GAIN control and sliders are not set to -12dB
Check that inputs and outputs are connected the correct way around
If overall frequency settings are above zero on average, reduce the Gain
Reduce frequency sliders with very high settings to check which is distorting
If output from mixer is XLR, connect via XLR to equalizer
If input to amplifier is XLR, connect via XLR from equalizer
If output from mixer is jack, connect via jack to equalizer
If input to amplifier is jack, connect via jack from equalizer
Increase Gain control(s) to compensate
Note: for further troubleshooting, refer equipment to qualified service personnel for testing
© Citronic 2011
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Citronic CEQ231 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Citronic CEQ231 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info