588930
4
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
2.5 Attaching the HAC
to the handlebar bracket
(the HAC must be attached to the handlebar bracket in
order to be used as a bike computer)
Remove the HAC from the wristband through turning
counter-clockwise. Insert it in the handlebar bracket and turn it
clockwise until it engages.
To check if the HAC has been attached correctly, please
turn the wheel a couple of times to see if the computer receives a
signal.
Last, but not least, pull the cable-ties of the speed transmitter tight
and cut off what is too long.
To remove the HAC from the handlebar bracket, turn it
counter-clockwise.
3. USING THE BUTTONS
The HAC display is divided into two parts: an upper part
and a lower part. One function is shown in each area, so that two
functions can be read simultaneously. This way the possible func-
tions on the displays can be combined as desired.
The two upper buttons are for the functions in the upper display, the
two lower buttons are for the functions in the two lower displays.
The following applies: The right button calls up main functions, the
left button calls up the accompanying sub-functions.
The buttons are abbreviated as follows in the operating instructions:
Upper Right button: UR-button
Lower Right button: LR-button
Upper Left button: UL-button
(this button can be used to increase values = Plus-button)
Lower Left button: LL-button
(this button can be used to decrease values = Minus-button)
Start/Stop-button:
The functions stopwatch and count-
down can be started/stopped by
short pressing the start/stop-button
(while depending function is shown in
the display).
Short pressing means 1 second
pressing, long pressing means 4 or
6 seconds pressing (as specified).
Every button press raises a short
signal tone.
4. BASIC SETTINGS
The HAC has two setting modes (these will be called mode
1 and mode 2 in the following instructions). To switch to setting
mode 1, press the UR-button for 4 seconds. To switch to setting
mode 2, press the LR-button for 4 seconds. In order to quit a
setting mode premature, press either the UR- or LR-button again for
4 seconds.
The following applies to both setting modes:
- Pressing the respective button (mode 1: UR; mode 2: LR) swit-
ches from one setting to the next setting.
- The UL-button and the LL-button change the settings (the UL-
button increases, the LL-button decreases) and shifts or switches
off.
If UL- or LL-button are pressed longer than 1 second, the value
changes faster.
4.1 setting mode 1
Press the UR-button for 4 seconds:
AH – Altitude Home (Primary setting
for altitude measurement)
Set with the UL- or LL-button
Standard value = „----“
Setting range min. = -200m or ft x10;
max.= 9000 m / 2952 ft x10
The HAC is equipped with a barometric altitude measure-
ment which automatically adjusts to changes in temperature,
however it may show a variation due to changes in the air-pressure
(e.g. during the night). In order to compensate these variations, you
may set an altitude when starting (e.g. your home, if you always start
out from there), which the HAC uses when you start a new
training round (recording). This setting should be changed if you start
from somewhere else (e.g. vacation). If the setting is not adjusted
(display „----“), the HAC uses the actual (displayed) altitude
when you start a new recording.
PC – PC-transmission mode
Start with UL- and LL-button short simultane-
ously
By pressing UL- and LL-button short simulta-
neously the transmission to the pc is started
(for this you need the interface HACtronic
an optional accessory ).
During the transmission the lower display counts from 0 to 100%.
PC-Interval – Set memory interval
Set with the UL- or LL-button
Standard value = 20 sec.
Setting range = 2, 5, 10 or 20 sec.
Here the memory interval, in which the
HAC stores data for the pc evaluation (2, 5, 10 or 20 se-
conds) can be adjusted. The maximum recording time is depending
on this interval (2/5 sec. interval = nearly 6 hours recording time, 10
sec. interval = nearly 12 hours recording time and 20 sec. interval =
nearly 24 hours recording time), see also chap. 6.1.
CI 1 – Circumference Bike 1
Set with UL- or LL-button
Standard value = 2080mm
Setting range min. = 500 mm,
max. = 3000 mm
4
URUL
LRLL
Start/Stop
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ciclo HAC 4000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ciclo HAC 4000 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ciclo HAC 4000

Ciclo HAC 4000 Gebruiksaanwijzing - Deutsch - 16 pagina's

Ciclo HAC 4000 Gebruiksaanwijzing - Français - 15 pagina's

Ciclo HAC 4000 Gebruiksaanwijzing - Italiano - 15 pagina's

Ciclo HAC 4000 Gebruiksaanwijzing - Espanõl - 16 pagina's

Ciclo HAC 4000 Gebruiksaanwijzing - Polski - 8 pagina's

Ciclo HAC 4000 Gebruiksaanwijzing - Dansk - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info