793221
20
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
20
GB
1. Put the cable 3 for latissimus (40) with screw end from
bottom side through the front big hole of top frame (11) so that
the ball of cable 3 (40) is below of top frame (11). Then put the
cable 3 (40) from top side through the second big hole of top
frame (11) and nally through top cover bracket (82). Finally
screw I into the pull rod (36) as arrows shows on gure.
2. Attach the two pulleys (19) with cable 3 (40) into the top
frame (11) and secure with hex bolts M10x70 (48), washers
(67) and nylon nuts M10 (64). Ensure that the cable 3 (40) lead
over the pulleys on top of the to frame (11).
3. Attach two pulleys (19) with cable 3 (40) and pulley covers
(20) into double pulley holder (25) and secure with hex bolt
M10x50 (50), washer 10//20 (67) and nylon nut M10 (64)
4. Attach one pulley (19) with cable 3 (40) and pulley cover
(20) into pulley holder at top frame (11) and secure with hex
bolt M10x50 (50), washer 10//20 (67) and nylon nut M10 (64).
5. Cover all screw heads of screws (48+50) and nuts (64) with
corresponding screw caps (74).
6. Connect the latissimus bar (15) at cable 3 (40) by using
carbine hook (3) after assembly complete. To storage the long
bar (15) you can put it on the appropriate holder in front of the
top fame (11).
1. Put the cable 2 for leg curler (39) with eye end through the
leg curler (4) so that the ball of cable 2 (39) is in front of the leg
curl (4) and put the cable 2 (39) with eye end through and big
hole of main frame (34).
2. Attach one pulley (19) with cable 2 (39) into the leg curler
(4) and secure with bolt M10x50 (50), washer 10//20 (67) and
nylon nut M10 (64).
3. Attach one pulley (19) with cable 2 (39) at main frame (34)
and secure with bolt M10x50 (50), washer 10//20 (67) and
nylon nut M10 (64).
4. Attach one pulley (19) with cable 2 (39) and pulley covers
(20) into bottom part of twisted pulley holder (26) and secure
Installation of cable 3 for lattissimus (40) with pulleys
(19).
Installation of cable 2 for leg curler (39) with pulleys (19).
STEP 9
STEP 10
3
15
74
40
48 67
67 74
11
40
82
36
25
74
64
67
20
19
20
25
50 67
74
19
64
19 20
20
with hex bolt M10x50 (50), washer 10//20 (67) and nylon nut
M10 (64).
5. Attach one pulley (19) with cable 2 (39) and pulley
covers (20) at base frame (17) and secure with bolt M10x50
(50), washer 10//20 (67) and nylon nut M10 (64).
6. Put the cable 2 (39) with eye end through the double pulley
holder (25) and enlarge the length of cable 2 (39) with two
carbine hooks (3) and short chain (46) to connect it nally at
appropriate position of base frame (17).
7. Cover all screw heads of screws (50) and nuts (64) with
corresponding screw caps (74).
34
67 64
74
46
3
3
26
25
5
50
67
74
39
17
4
19 4
64 67
39
67
50 74
74
Note: When you use leg curler for
exercising you should disconnect the
curl bar (12) with chain (45). To get
a smooth sliding cable system, you
may adjust the cable system roughly
at short chain (46) with carbine hooks
(3) through setting them into another
position. For smaller adjustments you
can use the screw end of cable 1 at
pull rod. Always x the position of this
screw with nut and take care that this
screw is minimum 12mm inside the
threat. For an easier sliding of the
weights at sliding tubes (5) you can
put a little bit lubrication oil at sliding
tubes.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Christopeit SP2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Christopeit SP2000 in de taal/talen: Nederlands, Duits, Engels, Frans, Pools als bijlage per email.

De handleiding is 6,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Christopeit SP2000

Christopeit SP2000 Aanvulling / aanpassing - Deutsch - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info