793221
16
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
16
GB
ASSEMBLY INSTRUCTIONS
Before beginning assembly, be sure to observe our
recommendation and safety instructions. Take out all
parts from cartons and lay down on the oor. Some parts
are pre-assembled.
1. Place the rear foot (18) at base frame (17) in the right way
on en even oor together so that the holes align and screw
them with hex bolt 10x65 (49), at washer 10//20 (67) and
nylon nut M10 (64) tightly.
2. Place the main frame (34) onto the base frame (17) and
screw it rst vertically with carriage bolt M10x65 (53), curved
washer 10//25 (71) and nylon nut M10 (64) tightly. Then tighten
the main frame (34) horizontally to the base frame (17) with
hex bolt M10x70 (48), at washer10//20 (67) and nylon nut
M10 (64).
3. Place the backrest (13) at the main frame (34) and screw
tightly by using hex bolt M8x65 (54) and curved washer 8//25
(72). Then mount the head pad (107) in the same way as the
back pad (13).
4. Cover all screw heads of screws (48+49+54) and nuts (64)
with corresponding screw caps (74+75).
1. Insert the sliding tubes (5) into the holes of rear foot (18)
and x them with hex bolt M8x60 (55), washer 8//16 (68) and
nylon nut M8 (65). Then cover all screw heads of screws (55)
and nuts (65) with screw caps (75+76).
Slide the bottom cover bracket (22), 2 rubber bumper (10),
the weight supports (83) and again 2 rubber bumper (10) onto
the sliding tubes (5). (Note: If you bought the option weight set
Art.-No. 9389 you put on the 2 additional weight plates (32)
instead of the weight supports (83)(Fig. 1). Then slide
the weight plates (32) over the sliding tubes (5) in correct
direction so that the locking pin (30) can be positioned under
the weight plate.
2. Slide the plastic ring (35) onto the pull rod (36) and secure
with limit bolt (37) in uppermost hole. Insert the pull rod (36)
into the weights (32).
3. Slide the rst weight plate (31) onto the sliding tubes (5)
and put the plastic washer 13//40 (1) on top.
4. Put the 2 adjustment screws (33) into the appropriate holes
of top cover bracket (82) as gure 2 shows and x them with
washers 8//16 (68) and nylon nuts M8 (65).
5. Slide the top cover bracket (82) onto the sliding tubes (5)
and insert the security pin (30). To adjust the weights, use the
security pin (30) and put it into desired position of the pull rod
(36). In this case, the higher the locking pin (30) is inserted, the
lower the weight load.
Installation of base frame (17), rear foot (18) and main
frame (34).
Installation of sliding tubes (5) and weights (31+32).
STEP 1
STEP 2
33
82
68
65
37
32
10
83
22
68 18
76 65
68
55
75
30
31
1
5
35
36
107
13
17 53
67
67
74
48
49
18
74 64 67
64
74
71
71
34
72 54
75
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Christopeit SP2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Christopeit SP2000 in de taal/talen: Nederlands, Duits, Engels, Frans, Pools als bijlage per email.

De handleiding is 6,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Christopeit SP2000

Christopeit SP2000 Aanvulling / aanpassing - Deutsch - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info