666999
4
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
A
A
s
s
s
s
e
e
m
m
b
b
l
l
i
i
n
n
g
g
Y
Y
o
o
u
u
r
r
T
T
e
e
l
l
e
e
s
s
c
c
o
o
p
p
e
e
1) Your Celestron telescope should include all of the following:
a. Tripod with center support bracket
b. Telescope tube with tube rings attached
c. Equatorial mount head
d. Two 1 ¼" eyepieces
e. 90˚ star diagonal
f. 5x24 Finderscope
g. 3x Barlow Lens
h. 5# Counterweight
i. Counterweight bar
j. Two slow motion cables
k. Eyepiece accessory tray
l. The Sky CD rom
2) To set up the tripod, spread the legs outward until they are fully extended. Extend the center portion of each of
the three tripod legs down 6-8". Use the three tightening screws located at the bottom of each leg to secure the
extended legs in place.
3) Place the accessory tray on top of tripod's center leg brace. Thread the tray's threaded post into the threaded
hole in the center of the leg brace.
4) Locate the equatorial mount and place the base of the mount through the hole in the center of the tripod
mounting platform. From underneath the tripod mounting platform, thread the mounting bolt with washer into
the threaded hole on the bottom of the equatorial mount.
5) Thread the latitude adjustment screws into the equatorial mount until both screws are touching the inside of the
mount and the mount can no longer pivot up and down.
6) Locate the counterweight bar and counterweight. Thread the threaded end of the counterweight bar into the Dec
axis of the equatorial mount. Remove the safety screw and washer from the other end of the counterweight bar.
Loosen the counterweight locking bolt so that the screw is no longer obstructing the center hole of the
counterweight. Slide the counterweight half way up the counterweight bar and tighten the locking screw to
secure the counterweight in place. Thread the safety screw and washer on to the end of the counterweight bar.
Figure 1
7) Slide the chrome end of the slow motion control cables onto the equatorial
mount gear shaft. See Figure 1. The longer cable should attach to the Right
Ascension axis and the shorter cable attaches to the Declination axis.
8) Remove the wing nuts from the threaded post at the bottom of the tube ring.
Place the telescope tube on top of the equatorial mount so that the threaded
posts slide through the holes on the equatorial mount. The declination slow
motion cable should extend towards the focuser end of the telescope tube.
Replace the wing nut and tighten to hold the telescope in place.
9) Remove the plastic cap covering the end of the focuser. Loosen the set screw
on the focuser so that it does not obstruct the inner diameter of the focuser.
Insert the chrome barrel of the star diagonal into the focuser and tighten the set
screw.
10) Loosen the set screw on the star diagonal so that it does not obstruct the inner diameter of the barrel. Insert the
chrome barrel of the 20mm eyepiece into the diagonal and tighten the set screw. See Figure 2.
4
4

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Celestron-POWERSEEKER-80-EQ---21048

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Celestron POWERSEEKER 80 EQ - 21048 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Celestron POWERSEEKER 80 EQ - 21048 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info