508111
5
Verklein
Vergroot
Pagina terug
1/51
Pagina verder
ENG-4
Automatic recognition of the speed sensor ID
The speed sensor has its own ID, and the computer measures in synchronization
with the ID.
Two speed-sensor IDs can be registered to one computer, which can automatically
identify two speed sensors once their IDs are registered in advance.
As a tire circumference is set to the speed sensor ID, wheel selection by manual
operation is no longer required, which was necessary with conventional units.
* The speed sensor currently recognized is indicated with a sensor icon (
or )
on the screen.
Procedure of automatic recognition
When the computer changes to the power saving screen, and then returns to the
measurement screen, automatic recognition of the speed sensor ID is performed
in the following procedure.
1. The computer searches the speed sensor ID signal, which had been synchro-
nized immediately before.
2. Once the sensor signal is received, the sensor icon for the speed sensor lights
up, and the computer starts the measurement.
When the speed sensor ID signal which had been synchronized immediately
before, cannot be received another sensor signal is searched.
3. When the computer receives another sensor signal, the sensor icon for the
other sensor lights up on the screen, and starts the measurement.
When another speed sensor ID signal cannot be received, the original sensor
signal is searched again.
The computer repeats synchronization through the procedure described above
even if it fails in synchronization for some reason, such as communication fail-
ure; in such cases however, it takes time for recognition.
* When any speed sensor signal cannot be received in 5 minutes,
/ is
turned off, and the computer enters the transmission-off status and changes
to the power saving screen after another 5 minutes.
Switching the ID by manual operation
The speed sensor ID can be forced to change manually, according to the menu
screen “Setting the tire circumference” (page 31). Use this operation in the
following cases.
• When the computer cannot recognize the intended sensor signal, since the 2
registered speed sensors are nearby and both are sending a sensor signal.
• When you want to switch the speed sensor ID immediately.
* Once you switch the speed sensor ID by manual operation, the computer con-
tinues to search only the speed sensor ID you switched when returning to the
measurement screen. When the computer cannot receive any sensor signal in
10 minutes, the power-saving mode is activated, and the computer changes
to the power saving screen. The computer searches through the procedure of
automatic recognition when it returns to the measurement screen.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cateye CC-TR310TW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cateye CC-TR310TW in de taal/talen: Engels als bijlage per email.

De handleiding is 3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Cateye CC-TR310TW

Cateye CC-TR310TW Gebruiksaanwijzing - Nederlands - 51 pagina's

Cateye CC-TR310TW Gebruiksaanwijzing - Deutsch - 51 pagina's

Cateye CC-TR310TW Gebruiksaanwijzing - Français - 51 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info