580402
45
Verklein
Vergroot
Pagina terug
1/47
Pagina verder
45
Introduction
How to install the
unit on your bicycle
Setting up the
computer
How to use the
computer
Setup of your PC
Uploading the
measurement data
Changing the
computer
configuration
Others
How to install the heart rate sensor (HR-11)
Heart rate is measured when the heart rate sensor is worn on the chest.
Warning!!! : This product must NOT be used by those who have a pacemaker.
• To avoid measurement errors, it is recommended to moisten the electrode pads with water.
• If your skin is sensitive, the electrode pad may be moistened with water and worn on a thin
undershirt.
• Chest hair may interfere with the measurement.
1
Attach the heart rate sensor to the HR strap.
Push it in until it clicks.
2
Insert the HR strap hook to the other end of the strap.
Wear the heart rate sensor with the HR strap, and adjust the length of the HR strap to fit
your chest size (under bust). Fastening the strap too tightly may cause discomfort.
* Wear the heart rate sensor so that the top of the sensor faces up.
* Ensure that the electrode pad is in direct contact with the
body.
* When your skin is dry, or wearing the heart rate sensor on
top of your undershirt may produce measurement errors.
To avoid errors, moisten the electrode pad.
Watch video
(YouTube)
Click the button, then a browser will open and a
video will be played back.
2
Temporarily secure the magnet
1
Temporarily secure the cadence magnet inside the crank
with nylon ties, so that it faces the sensor zone on the
CADENCE side.
2
Turn the sensor arm, and temporarily secure the wheel
magnet to the spoke that faces the sensor zone on the
SPEED side.
* When the speed sensor is not positioned appropriately in respect
to the two magnets (of
CADENCE
and
SPEED
), move the speed
sensor back and forth so that it is positioned properly. After you
move the speed sensor, adjust the position so that the two mag-
nets face the relevant sensor zone.
3
Adjust the distance to the magnet
1
Tilt the speed sensor so that the distance be-
tween the cadence magnet and the CADENCE
side of the speed sensor is about 3 mm, and
firmly secure it with the nylon ties.
2
Turn and adjust the sensor arm so that the
distance between the wheel magnet and the
sensor arm is about 3 mm, and firmly tighten
the sensor screw.
4
Securing various parts
Firmly tighten the nylon ties, sensor screw and magnet of
the speed sensor, and check for any loosening.
* For steel axle pedals, the cadence magnet can be magneti-
cally secured on the pedal axle. Make sure to remove the
double-sided tape from the magnet when doing this.
3 mm
(1/8”)
3 mm
(1/8”)
3 mm (1/8”)
Cadence
magnet
Speed sensor
CADENCE side
Wheel magnet
Heart rate sensor
HR strap
Hook
Back
Electrode pad
Cut extra length of the
nylon tie with scissors.
Sensor arm
SPEED side
Sensor
screw
Cadence
magnet
Wheel magnet
Sensor zone
Nylon ties
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cateye CC-GL51 Stealth evo plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cateye CC-GL51 Stealth evo plus in de taal/talen: Engels als bijlage per email.

De handleiding is 3,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Cateye CC-GL51 Stealth evo plus

Cateye CC-GL51 Stealth evo plus Gebruiksaanwijzing - Nederlands - 47 pagina's

Cateye CC-GL51 Stealth evo plus Gebruiksaanwijzing - Deutsch - 47 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info