36042

Casio QW2471 Handleiding

3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
USER’S GUIDE 2471
3
With a Reference Altitude
• If you set a reference altitude, the watch
uses that value when calculating altitude
based on air pressure.
• To determine the height of a tall building,
set the reference altitude to 0 on the
ground floor. Note, however, that you may
not be able to get a good reading if the
building is pressurized or air-conditioned.
• When mountain climbing, you can set the
reference value in accordance with a
marker along the way or altitude
information from a map. After you do this,
the altitude readings produced by the
watch will be more accurate than they
would without a reference altitude.
400
B
A
To take an altitude reading
Pressing E in the Timekeeping Mode or in any of the other sensor modes
enters the Altimeter Mode. The watch automatically starts altitude
measurement, and displays the results.
• See “About Altitude Measurements” for important information.
• Altitude is displayed in units of 5 meters (20 feet).
• The measurement range for altitude is –700 to 10,000 meters (–2,300 to
32,800 feet).
About one
second later
Altitude graph (current altitude flashing) (unit: 10m/40 ft.)
Altitude
Timekeeping Mode time
▲
• The measured altitude may be a negative value in cases where there is a
reference altitude value set or because of certain atmospheric conditions.
• The displayed altitude value changes to
xxxxx meters (or feet) if a
measured altitude falls outside the measurement range. The altitude value
will be displayed again as soon as the measured altitude is within the
allowable range.
• You can change the unit of measurement for the displayed altitude values
between meters (m) and feet (ft). See “To change the Altitude Units”.
About Altitude Measurements
There are two types of altitude measurements: those for displayed data
(Altimeter Mode measurements) and those for memory data (Memory
measurements).
Altimeter Mode measurement
You can perform Altimeter Mode measurements in the Altimeter Mode only,
and an altimeter measurement operation starts whenever you enter the
Altimeter Mode.
During the first three minutes after entering the Altimeter Mode, ALTI flashes
on the display and measurements are taken every five seconds. After that,
the interval between measurements depends on whether you are using the
Short Mode (1-minute intervals) or the Long Mode (2-minute intervals).
• Long Mode is the default setting. See “Memory measurement” for
information about the Short Mode and Long Mode.
• If you do not perform any operation while in the Altimeter Mode, the watch
automatically returns to the Timekeeping Mode after four or five hours in
the Short Mode, or after nine or 10 hours in the Long Mode.
Memory measurement
The memory measurement operation stores the following data in watch
memory. Note that each time you perform a memory measurement operation,
it creates a new set of records, replacing the set of records currently in
memory. Memory measurement continues to be performed (indicated by the
REC indicator flashing on the display) even if you change to another mode.
Measurement start time, date, and altitude: 1 record
Automatic altitude readings and time, at fixed interval: Up to 39 records
Measurement end time, date, and altitude: 1 record
The watch also calculates the following values using measured data and
maintains one record for each in memory.
Relative altitude (altitude difference between start point and current altitude or
measurement end altitude)
Measurement time
Maximum altitude (highest measured altitude in memory)
Total ascent (total of ascents (A + B))
Cumulative total ascent (total of all measured altitude values in memory)
Start point
Stop point
Maximum altitude
A
B
C
• Starting a new measurement automatically clears relative altitude,
measurement time, maximum altitude, and total ascent values currently in
memory.
• Starting a new measurement does not clear cumulative total ascent. This
value continues to increase until it reaches 99,995 meters (327,983 feet).
After that, it reverts to 0 and starts again.
• The interval between memory measurements depends on whether the
Short Mode or the Long Mode is selected.
Short Mode: 5-minute interval
Long Mode: 15-minute interval
• Relative altitude, cumulative total ascent, and maximum altitude data is
calculated at regular intervals, depending on the Long Mode/Short Mode
setting. In both modes, calculations are performed every five seconds for the
first three minutes. After that, calculations are performed every minute in the
Short Mode and every two minutes in the Long Mode.
To select the Short Mode or Long Mode
1. In the Altimeter Mode, hold down A until the
display clears. After four or five seconds,
either
OFF or the current reference altitude
value (if set) starts to flash, which indicates
the setting screen.
•
OFF indicates no reference altitude.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
• Note that you will not be able to change the
Short/Long Mode setting if a memory
measurement operation is in progress.
2. Press D twice.
• This causes either 0:05 (Short Mode) or
0:15 (Long Mode) to appear, which
indicates the current mode setting.
3. Each press of E toggles between the Short
Mode and Long Mode.
4. Press A to exit the setting screen.
To perform memory measurement
Hold down E for about one second until REC
flashes, which indicates that memory
measurement has started.
• Memory measurement stops automatically
after there are 41 records accumulated in
memory. When you want to stop a memory
measurement operation manually, hold down
E for about one second until REC disappears.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
• While a memory measurement operation is in progress, press A to toggle
between the Standard Altitude screen and the Relative Altitude screen.
Note
• REC flashes on the display while a memory measurement operation is in
progress.
• Starting the memory measurement operation deletes any altimeter data
(except for cumulative total ascent data) currently in memory (and its graph)
and replaces it with the new data. Note that you cannot delete memory
contents manually.
Relative altitude
▲
▲
Press A.
Altitude
Timekeeping Mode time
Standard Altitude
Screen
Relative Altitude
Screen
Measurement time
REL indicator
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
• You can recall data in memory using the Data Recall Mode.
Setting a Reference Altitude
After you set a reference altitude, the watch adjusts its air-pressure-to-altitude
conversion calculation accordingly. The altitude measurements produced by
this watch are subject to error caused by changes in air pressure. Because of
this, we recommend that you update the reference altitude whenever one is
available during your climb.
To set a reference altitude
1. In the Altimeter Mode, hold down A until the
display clears. After four or five seconds,
either
OFF or the current reference altitude
value (if set) starts to flash, which indicates
the setting screen.
2. Press E (+) or B (–) to change the current
reference altitude value by 5 meters (or 20 feet).
• You can set the reference altitude within the
range of –10,000 to 10,000 meters (–32,800
to 32,800 feet).
3

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Casio-QW2471

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio QW2471 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio QW2471 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Casio QW2471

Casio QW2471 Gebruiksaanwijzing - Nederlands - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info