624818
3
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Operation Guide 5229
E-20
Lap Time
Lap time readings appear in the left digital dial. They show
the time elapsed since the last lap time reading was
taken.
If you want the watch to calculate the speed of each lap
(when all of the laps are the same distance), specify the
lap distance for the distance setting (page E-15).
If you want the watch to calculate the speed of the entire
race, specify the race distance for the distance setting
(page E-15). A speed will be indicated each time you
take a lap reading, but these lap speeds will not indicate
actual speed of the entire race.
To set up the stopwatch to take lap time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
If you need to reset the stopwatch to all zeros, press A.
2. Make sure that
LAP
(lap times) is shown in the left digital dial.
If
SPL
(split times) is displayed, press A to toggle it to
LAP
.
Lap time
E-21
To perform a lap time measurement
Select lap time (
LAP
) measurement and then perform the
following button operations.
D Start A Lap* A Lap* D Stop A Reset
* Lap time remains frozen in the left digital dial for about
12 seconds. After that, elapsed time measurement
reappears.
You can press A to take lap readings as many times as
you like.
While a lap time is displayed, the right digital dial will
alternate between the lap number (#01 to #99) and the
lap hour value. If you take more than 99 lap readings,
the lap number will restart from #00 following lap #99.
Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
lap.
Lap number
Speed hand
(calculated)
Minutes
Seconds
1/1000 seconds
Hours
E-22
Split Time
Split time readings appear in the left digital dial. They
show the time elapsed since the beginning of the current
time measurement.
If you want the watch to calculate the speed of the race,
specify the race distance for the distance setting (page
E-15).
For split time readings, you can specify the total race
distance only. Though the watch will indicate a speed
each time you take a split reading, they will be based on
the total race distance, and so they will not indicate
actual intermediate split speeds.
To set up the stopwatch to take split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
If you need to reset the stopwatch to all zeros, press A.
2. Make sure that
SPL
(split times) is shown in the left digital dial.
If
LAP
(lap times) is displayed, press A to toggle it to
SPL
.
Split time
E-23
To perform a split time measurement
Select split time (
SPL
) measurement and then perform
the following button operations.
D Start A Split A Split Release* D Stop
A Reset
* The split time is released automatically if you do not
press A within about 12 seconds.
You can press A to take split readings as many times
as you like.
The stopwatch continues elapsed time measurement
internally while a split time reading is displayed.
Pressing A while a split time is displayed will switch
back to normal elapsed time measurement. The elapsed
time will appear in the left digital dial.
You also could press D to stop elapsed time
measurement instead.
Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
split (which is the overall elapsed time).
Hours
Speed hand
(calculated)
Minutes
Seconds
1/1000 seconds
E-24
To measure times with the stopwatch
Elapsed Time
Lap Time
Split Time
D
Start
Stop Reset
D
➤➤
A
D
Start
(
SPL
displayed)
Split Split release Stop
A
D
A
➤➤
Reset
A
D
Start
(
LAP
displayed)
Lap
(Lap01)
Stop Reset
D
A
A
➤➤
A
Lap
(Lap02)
E-25
Countdown Timer
You can set the countdown start time within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Seconds
Auto-repeat off
Start time
(Hours : Minutes)
E-26
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown in the left digital
dial.
When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
If auto-repeat is turned off, the countdown time is reset to its starting value
automatically after the alarm stops.
If auto-repeat is turned on, the countdown will restart automatically without pausing
when it reaches zero.
The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-27
To configure countdown start time and auto-repeat settings
1. While the countdown start time is shown in the left
digital dial in the Countdown Timer Mode, hold down A
for about three seconds until the hour setting of the
countdown start time starts to flash. This is the setting
mode.
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-26) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
3. Perform the following operations, depending on which setting is currently selected
in the left digital dial.
While the start time setting is flashing, use D (+) and B (–) to change it.
To toggle auto repeat between on and off, press D while the on/off setting is
flashing in the left digital dial.
Start time
(Hours : Minutes)
Auto-repeat on
E-28
4. Press A to exit the setting mode.
The auto-repeat on (
) indicator is displayed on the Countdown Timer Mode
screen while this function is turned on.
E-29
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
Currently selected
World Time City
World Time
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 5229 - GA-201 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 5229 - GA-201 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Casio 5229 - GA-201

Casio 5229 - GA-201 Gebruiksaanwijzing - Deutsch - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info