481328
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
42 HWX / HQX
GB - 7
ENGLISH
Start/stop
(button B)
When the air conditioner is not in operation, the controller readout
will display the time of day only (in case other symbols are lit, turn
controller off by pressing button B
).
Press button B
to start the air conditioner; indicator N on the
unit will appear and be illuminated.
All selected and memorized functions will light up and appear; the
unit will operate according to the functions selected.
If the unit does not acknowledge the starting signal by emitting a
sound (beep) and indicator N
does not light up, it is necessary
to turn the controller off by pressing button B
and then repeat the
operation.
Press button B
to stop the air conditioner. All indicators on the
unit will go out, and controller will display only the current time.
If the unit does not stop, turn the controller on (by pressing button B
) and repeat the operation. In some special operating conditions
the fan will continue to run for 30 sec. after the unit stops; the
indicator Q
on the unit will lighten.
If button B
(air conditioner starting) is pressed too soon after a
stop, the compressor will not start for 3 minutes due to the inherent
protection against frequent compressor cycling; in this case
indicator Q on the unit will also light up.
The unit will only emit a beep, when the signals are received
correctly.
Timer mode on/off
(button C)
Press this button when you want the air conditioner to operate in
the timer mode according to the time programs selected with button
G
.
When this function is on, indicator P
on the unit is lit.
After a power failure, indicator P
will flash and the unit will run in
the last operating condition before the power cut.
Power failures will deactivate the Timer mode: to reactivate the
Timer mode, press button C
twice.
Selection of the operating mode
(button D)
With this button the operating mode of the air conditioner can be
selected. Different options are available depending on the unit
model. By repeatedly pressing this button the available modes will
be selected in sequence and the relevant symbols will appear on
the display, while the unit will acknowledge signal receipt with a
confirming beep.
Symbol on display
Cooling with dehumidification.
Heating (where available).
Automatic mode.
The air conditioner will automatically switch from heating
(where available) to cooling and vice versa in order to
maintain the selected temperature.
Dehumidification only.
The air conditioner extracts moisture from the air without
sensibly changing the room temperature.
Ventilation (fan only)
Use of the remote controller
Setting desired temperature
UP
(button E)
DOWN
(button F)
Pressing the UP (E ) and DOWN (F ) buttons will increase or
decrease the temperature set from the previously set value. The
unit will confirm signal receipt with a beep, and the value of the set
temperature on the display will change accordingly.
The temperature can be set between 18°C and 29°C at 1 degree
intervals.
In the cooling mode, if the temperature selected is higher than the
room temperature the unit will not start; the same applies for the
heating mode, if the selected temperature is lower than the room
temperature.
Setting the timer programs
(button G)
By pressing button G it is possible to choose one of the following
programs in sequence:
Symbol on display
No Continuous operation
simbol (timer off)
Start time program
Stop time program
Combined program: unit will automatically cycle on and off
as programmed
Set start time
Press button G
until the symbol indicating unit start program will
appear on display under the word TIMER.
The time appearing on display shows the starting hour
previously programmed:
You can set your personalized new start time by pressing buttons
H
and I until the desired time appears. Each press of the
button will change the time up or down by 15 min. between 0:00
and 23:45.
Press button C
to confirm your selection: indicator P on the
unit will light up and the air conditioner is ready to start at the
selected time.
If the unit is in operation when you send your confirmation by
pressing button C
, it will turn off and
restart at the time now programmed.
Set stop time
Press button G
until the symbol indicating unit stop program
appears on the display under the word TIMER. The time appearing
on display shows the stop time previously programmed; you can
now set your personalized new stop time by proceeding as for the
start time.If the unit is turned off when you send your program
confirmation by pressing button C
, it will start up, and then turn
off at the time now programmed.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Carrier 42 HQX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Carrier 42 HQX in de taal/talen: Nederlands als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info