469906
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
11
Preparation of start
This Carrera DIGITAL 124 vehicle ideally matches the Carrera track
system scale 1:24.
vehicle construction depends on the model.
Besides replacing the guide keel, the complete magnet units
(
+
) as well as the distance plates (a) beneath the magnets
may be removed and added respectively. The more distance plates
(a) and magnet units (b) are used the stronger the magnetic eect
is on the track. As soon as a magnet is installed, the metal plate (c)
has to be used. Depending on the car type it is advisable to remove
or not to implement the spacing plate when using a Carrera crossing
or high banked curve. With those track elements being used, slight
driving noises may occur. These are caused by the cars´ scale au-
thenticity and do not have any inuence on a faultless operation.

To ensure proper and continuous driving, slightly fan out the ends
of the contact brushes
and bend them towards the track as per
g.
. Only the end of the contact brush should have contact to the
track and may be cut o slightly in case of wear. Dust and abrasion
should be removed from track material and sliding contacts from
time to time.
Preparation of start and
points function
Make sure that the car’s guide keel is located inside the
track slot and that the double sliding contact is in contact with the
current carrying track.
Place the cars onto the connecting track.
    

Replacement of double
contact brushes and guide keel
In case the car is lifted, the rocker bar folds up slightly (g.
).
For changing the guide keel or the double contact brushes the
rocker bar can be folded up widely according to g.
.
 in cars without height adjustable chassis, the rocker arm can-
not be entirely folded up !!!
For changing the guide keel and the double contact brushes the
guide keel should be removed rst.
Afterwards both double contact brushes can be removed and
changed. Please take care that in stage one the upper contact
brush
is only pulled out partly and in stage two the double
contact brush is pulled out completely with the contact brush
For inserting please proceed the same way.
Height adjustment
rocker bar/chassis

cars without height adjustable chassis do not have an adjust-
ing screw for the rocker arm.
In order to variably reduce or enlarge the distance between the car
and the track, the screw (a) in g.
has to be brought either into a
lower or into a higher position.
Screwed in = minimum ground = clearance in the front
Unscrewed (as far as possible) = maximum ground clearance
in the front
 With the screw being xed in the highest position it
is not guaranteed that the front wheels will have contact with the
track.
Height adjustment
car chassis



When starting with the modication, the car’s upper part has to be
unscrewed from the chassis and the following steps have to be car-
ried out.
Remove the cable joints (g.
). Take the front axle attachments
out of the chassis according to g.
. Take the distance plate (a)
out of the chassis and put it into the front axle attachment (g.
).
Insert the front axle attachment in the chassis again (g.
) and
screw it tight.
When tting the axle attachment you have to make
sure that the position screw’s head (b) for the rocker bar points to
the bottom.

When modifying the rear axle the following points need to be ob-
served.
Remove the cable joint for the rear light and the engine block to the
board according to g.
. Unscrew the entire additional magnet
unit at the cars bottom (g.
), unscrew and take out the engine
block (g.
), take out the distance plate (b) and the magnet base
plate (a). Turn the magnet base plate by 180° (g.
) and put it in
the chassis again (g.
). Screw the additional magnet unit tight
and place the distance plate on top of the magnet base plate.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Carrera Digital 124 - 23607 TITANS OF RACING bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Carrera Digital 124 - 23607 TITANS OF RACING in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info