RGB/SCART
Use a SCART/Peritel cable to connect to the 21-pin scart input jack of a
TV. SCART carries both audio (stereo) and video (as either Composite,
S-Video or RGB) at the same time.
Analog Video Outputs
Composite — Connect to your television via 75 ohm RCA/phono cable
designed specifically for video use.
S-Video — Connect to your television via dedicated S-Video cable.
Component — Connect to the YCbCr or YPbPr terminals of a television
set via three 75 ohm RCA/phono cables designed specifically for video
use.
HDMI Out
HDMI (High-Definition Multi-Media Interface) is a purely digital
connection that can carry both audio and video. Use a dedicated HDMI
cable to connect to a TV/monitor with a compatible HDMI input.
540D V2azur
5
Rear panel connections
ENGLISH
AC power socket
Once you have made all audio and video connections, plug the IEC type
AC power cable into the rear of the unit and an appropriate mains
socket, and then switch on. Your DVD player is now ready for use.
Power On/Off
Switches the unit on and off.
Control Bus
In — Allows un-modulated commands from multi-room systems or other
components to be received by the unit.
Out — Loop out for Control Bus commands to another unit.
IR (Infra-Red) Emitter In
Allows modulated IR commands from multi-room systems or IR repeater
systems to be received by the unit. Commands received here are not
looped out of the Control Bus. Refer to the Custom Installation section
of this manual for more information.
Digital Outputs
Digital audio outputs are normally used to connect to a suitable Audio/
Video Receiver for surround sound decoding (output must be set for
‘RAW Bitstream’ — refer to the Audio Setup section). These outputs can
also be used to connect to a separate DAC or digital recording device
(output must be set for ‘PCM Stereo’ — see Audio Setup section).
Toslink Optical — Use a high quality TOSLINK fibre optic cable.
S/P DIF Co-axial Digital — Use a high quality 75 ohm digital RCA/Phono
interconnect cable designed specifically for digital audio use.
5.1 Channel Audio Out
If Downmix is set to ‘Off’ in the Speaker Setup section of the 540D V2’s
Setup menus, these sockets provide 5.1 output from the 540D V2's
built-in Dolby Digital/Pro Logic II decoder. This can be used to connect
to the 5.1 audio line-level inputs of an amplifier/AV receiver or amplified
speaker package if required.
If Downmix is set to ‘On’, the Left and Right outputs only are active and
provide a stereo downmixed output.
Stereo Audio Out
A separate permanent Stereo output (or Stereo downmix in the case of
multi-channel material) is available for connection to the analog stereo
inputs of an amplifier/AV receiver, etc. This is the best connection to use
for listening to CDs.
1
2
3
4
6
7
1
2345
6
8
9
10
7
5
9
8
10
Note: The preferred connection method for video sources is always
HDMI (highest quality, and can also carry audio in some
circumstances), then Component Video, RGB/SCART, S-Video, and
Composite Video (lowest quality). The HDMI and Component
outputs also support Progressive Scan which gives better picture
quality if supported by your TV.
Important Note
This unit has been designed to play video DVDs,
compact discs, recordable CDs (CD-R) and
rewritable CDs (CD-RW) bearing the identification
logos shown here. No other discs can be used. The
CD-R/CD-RW discs should contain properly recorded
TOC (Table of Contents) information so that they can
be played back. This unit can play only the discs
recorded in the CD-DA format designed for music
reproduction. Do not attempt to play a disc on this unit containing
other data, such as a CD-ROM for PCs.
