656740
5
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
851Wazur
ENGLISH
5
Rear panel connections
1. Loudspeaker terminals
For normal wiring, connect the wires from your left channel loudspeaker
to the LEFT + & - terminals, and the wires from the right channel
loudspeaker to the RIGHT + & - terminals. In each case, the red terminal
is the positive output and the black terminal is the negative output.
Other dual mono schemes are also possible if two 851Ws are used.
Refer to later sections of this manual for more information.
Use speakers with a nominal impedance of between 4-8 ohms. Care
should be taken to ensure no stray strands of wire short the loudspeaker
outputs together. Please ensure that the loudspeaker terminals have
been tightened completely to provide a good electrical connection. It is
also possible for the sound quality to be affected if the screw terminals
are loose.
Audio input types
The 851W features either unbalanced (phono/RCA) or balanced (XLR)
input connections. Either type may be used but not both at the same
time. The balanced connection is the higher quality option and can reject
noise and interference in the cable when used with other equipment
that supports this function. An XLR connector is wired Pin 1 - Ground; Pin
2 - Hot (in-phase); Pin 3 - Cold (phase-inverted).
Use the Left and Right Input Type switch (Item 4) to select the connection
type you wish to use. When using either the balanced or unbalanced
input, make sure that no cables or equipment are connected to the
unused input, as this may degrade operation. The unused input does
not need to be terminated and this should not be done.
2. Balanced Audio
For connection to the balanced XLR outputs of suitable pre-ampliers
that have this kind of output (such as our own 851E model). The pre-
amplier used should be capable of providing at least 1V rms of output
per phase (i.e. at both of + and – terminals of the XLR, more is also ne).
Nearly all modern pre-ampliers full this requirement.
3. Unbalanced Audio
For connection to the normal (single ended) RCA/Phono outputs of a
suitable pre-amplier (such as our own 851E model). The pre-amplier
used should be capable of providing at least 1V rms of output (more is
ne). Nearly all modern pre-ampliers full this requirement.
4. Input Type switch
Use to select a balanced or unbalanced connection type for the input.
5. Stereo/Mono mode switch
Switches the 851W between ‘normal’ Stereo operation (where one
851W is used for a pair of speakers) and Mono operation (where two
851W’s are used one for each speaker). Refer to later sections of this
manual for more information.
6. Mono mode switch
When Mono mode has been selected, switches the 851W between Bi-
amped Mono and Bridged Mono. Refer to later sections of this manual
for more information.
7. Control Bus
In - Allows un-modulated commands from multi-room systems or other
components to be received by the unit.
Out - Loop out for Control Bus commands to another unit.
The 851W can also be switched between On and Standby mode by
connecting the Control Bus output of an 851E pre-amplier to the
Control Bus input of the 851W. Refer to the ‘Power syncing’ section of
this manual for more information.
8. Trigger In, Out/Thru
For Custom Install use or with preamps and with trigger outputs, the
851W can be turned on and off (i.e. brought in and out of Standby
mode) by the presence of 5-12V DC at the Trigger input. A trigger input
will also produce an internally generated 12V DC trigger output at the
Output/Thru connection. Turning the 851W on from the front panel also
produces a 12V DC trigger output at the Output/Thru connection. This
can be used to turn on/Standby other connected power ampliers or
other equipment if desired. Refer to the ‘Power syncing’ section of this
manual for more information.
9. IR (Infra-Red) Emitter In
Allows modulated IR commands from multi-room systems or IR repeater
systems to be received by the unit. Commands received here are not
looped out of the Control Bus. Refer to the ‘Custom installation’ section
for more information.
10. AC power socket
Once you have completed all connections to the unit, plug the AC power
cable into an appropriate mains socket then switch on. Your unit is now
ready for use.
11. Power On/Off
Switches the unit on and off. If the 851W is not going to be used for long
periods of time it should be turned off using this switch.
12. Mains Voltage Selector Switch (CU version only)
Switches the 851W mains voltage between 100V and 115V.
Note: For use by Cambridge Audio service personnel only!
1
2 23 34 4
6
5
11
10
7
8
9
12
1
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Cambridge-Audio-AZUR-851W

Zoeken resetten

  • Ik heb sinds 2016 een Cambridge Audio 851W eindversterker en kan hem niet meer aanschakelen,de lampjes van protection branden heel lichtjes.
    Ik heb alle kabels losgekoppeld en het probleem blijft bestaan.
    Ik heb alles geprobeert maar niets helpt. Gesteld op 22-9-2020 om 20:42

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cambridge Audio AZUR 851W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cambridge Audio AZUR 851W in de taal/talen: Engels als bijlage per email.

De handleiding is 10,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Cambridge Audio AZUR 851W

Cambridge Audio AZUR 851W Gebruiksaanwijzing - Nederlands - 13 pagina's

Cambridge Audio AZUR 851W Gebruiksaanwijzing - Deutsch - 13 pagina's

Cambridge Audio AZUR 851W Gebruiksaanwijzing - Français - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info