169032
4
Verklein
Vergroot
Pagina terug
1/34
Pagina verder
E - 3
Installation
INSTALLATION CAUTION
1. Before finally installing the unit, connect the
wiring temporarily and make sure it is all
connected up properly and the unit and
system work properly.
2. Use only the parts included with the unit to
ensure proper installation. The use of un-
authorized parts can cause mal functions.
3. Consult with your nearest dealer if install-
ation requires the drilling of holes or other
modifications of the vehicle.
4. Install the unit where it does not get in the
driver's way and cannot injure the
passenger if there is a sudden stop, like an
emergency stop.
5. If installation angle exceeds 30° from
horizontal, the unit might not give its
optimum performance.
6. Avoid installing the unit where it would be
subject to high temperature, such as from
direct sunlight, or from hot air, from heater,
or where it would be subject to dust dirt or
excessive vibration.
7. Be sure to remove the front panel before
installing the unit.
Fitting the outer sleeve
Fitting the support strap
Remove the transit screws
from the top of the car radio.
Connect the fixing screw to the
rear of the car radio.
Remove the outer sleeve
and place into the
dashboard.
Bend the support strap to
suit the dashboard
aperture and fix to the
underside of the dash
board using the screw
and washer.
Make sure that it is not
angled more than 30°.
Slide the car radio into the
outer sleeve and connect the
spring washer and nut to the
fixingscrew.
DON’T FORGET! Bend the metal tabs on the
outer sleeve outwards and downwards to stop
the sleeve from moving.
30°
Removing the detachable
front panel
Attaching the detachable
front panel
Press the panel release button
on the front panel.
Attach the front panel at the right
hand side first, and then push
the front panel forwards to
lock it securely into place.
DON’T FORGET!
Always turn off the
car radio before
removing the front
panel.
Fixing Screw
Spring Washer
and 5mm Nut
Screw and Washer
Removing the unit
Din Rear-mount
Insert fingers into the
groove in the front of frame
and pull out to remove
the frame.
Insert the levers supplied with
the unit into the grooves at
both sides of the unit as
shown in figure until
they click. Pulling the
levers makes it possible
to remove the unit from
the dashboard.
Fra me
a
b
screw
dashboard
bracket
screw
hook
hook
Installation using the screw holes on the sides of
the unit.Fastening the unit to the factory radio
mounting bracket.
NOTE: The mounting box, outer trim ring and
half-sleeve are not used for this method
installation.
Panel Release
button
2
1
NOTE: If the D.C.P is dirty,
wipe off the dirt with soft,
dry cloth only. And use a
cotton swab soaked in
isopropyl alcohol to clean
the socket on the back of
the D.C.P.
UP SH
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Caliber mcd 786 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Caliber mcd 786 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Caliber mcd 786

Caliber mcd 786 Snelstart handleiding - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info