4
ENGLISH
3
ENGLISH
2
• The Caliber Evolution amplifiers feature a built-in variable crossover which allows you to fine-tune
your amplifiers response as you like it. Either for the Full Range sound, in which case the HPF-FULL-
LPF switch remains in its FULL position, or you can specifically select the High-Pass-Filter (HPF) or
Low-Pass-Filter (LPF) to adjust to your speakers requirements.The built-in variable crossover can
be adjusted in a range from 50Hz - 250Hz.
SPEAKER OUTPUT
• All the Caliber Evolution amplifiers have Stereo/Bridgeable Tri-Mode speaker output terminals.The
amplifier has its own stereo/bridge switch built-in, so there is no need to select a stereo or bridged
mode.You can connect the speakers to each channel in stereo mode, and simultaneously connect
a sub-woofer to the speaker terminal in a bridged mode.
•Pay attention in connecting your speakers and/or sub-woofers. Be sure to observe correct speaker
output connections for front, rear and their polarity.
In the stereo mode, connect the right speaker output to the right speaker and the left to the left.
Connect the positive (+) output to the positive (+) speaker terminal and the negative (-) output
to the negative (-) speakerterminal.
• In the bridged mode connect the right (+) positive to the positive speaker terminal and the left (-)
negative to the negative speaker terminal.
• Do not use the negative speaker output commonly for left and right speakers (common ground).
Improper polarity causes a loss of bass response.
• Never connect the negative speaker output to the chassis of your vehicle. This can cause severe
damage to your Car Audio System.
AMPLIFIER ADJUSTMENTS
You will get the best result if you adjust the front and rear channels separately.
• Unplugg the input for the rear channel and start with the front channel.
• Put the input level adjustment knob to the minimum.
• Put the volume of your radio to 3/4 of the maximum.
•Now adjust the input level of the front channel. Slowly turn up the input level and listen carefully
untill you hear the amplifier begin to distort. A Caliber Amplifier “clips” very softly, so this can
sometimes be a difficult adjustment.
• Once the front channel is fine-tuned to your satisfaction, you can plugg in the input for the rear
channel and unplugg the front channel input.Repeat the adjustments as we described them here above.
• Plugg in the front channel input again,and let your amplifier play on both the front and rear channels.
Listen once again very carefully if your front and rear channels are harmoniously playing together,
and make some final adjustments if necessary.
• Adjust the Bass Boost to your personal sound.
CALIBER WARRANTY
Due to the complexity of our products, we strongly recommend that this amplifier is installed
by your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for
12 month from the date of purchase.
If you install this amplifier yourself, we wish you lots of fun and succes in doing so. If you follow
our guidelines,you’ll get the best result.Our warranty,however, will be limited to and not exceed
30 days from the date of purchase.
FEATURES
•Bridgeable outputs.
•’Tri-mode’ output capability, simultaneous stereo & bridged mono set up is possible.
• Pulse Width Modulated (PWM) MOSFET Power Supply.
•Variable input sensitivity: RCA input 0.5V to 15V.
• Thermal-, Overload- and Shortcircuit protection.
• Excellent muting circuitry assures no turn on/off ‘pops’.
• Built-in High Pass / Full Range / Low Pass Filter switch on channel 1 and 2.
• Built-in High Pass / Full Range / Low Pass Filter switch on channel 3 and 4.
• Built-in High Pass / Full Range / Low Pass Filter switch on channel 5.
• Variable BassBoost 0dB - +18dB
• Chrome plated power connectors for optimal power distribution.
• European design and engineering.
• Chrome plated speaker connectors for optimal signal output.
MOUNTING
The amplifier has to have at least 5cm (2”) ventilation space at all sides, to allow the heat to rise
away from the amplifier. Be sure that the power and signal cables can enter and leave the amplifier
in a straight line, to avoid the risk of malfunction. Always place the power- and signalcables at
opposite sides of the vehicle to reduce any noises.
The amplifier should be protected from exposure to moisture and direct sunlight.
Mark the mounting surface using the amplifier as a template, then drill 2.5mm (1/8”) diameter holes
at the marked locations and mount the amplifier using the supplied self-tapping screws.
INSTALLATION
Remember to always disconnect battery ground before working on a vehicle’s electrical system!
Always place a fuse or circuit breaker no more than 30cm (12”) from the battery, no greather than
the fuse(s) of your amplifier for optimal protection.
GETTING YOUR POWER STARTED
• First, the +12V terminal is connected directly to the battery of your car. Use a cable of at least
25mm
2
, and make sure that the connectors are of the same value.
Don’t forget the extra “Vehicle protection” fuse.
The 12V + terminal should NOT be connected to the car fuse box.
• Second,the ground terminal (GND) must be fastened securely to the chassis of the vehicle with the
same mm2 cable as the positive cable (the same amount of power has to run through it). Ensure
that all paint, undercoating or any other insulation is removed from the area where you want to
make your ground connection to.
•Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and CD-players
have an output terminal for connection of the REM of an amplifier. If you don’t have such an out-
put, a separate switch must be installed to control your amplifiers on/off function.
SIGNAL INPUT
• The RCA’s to your left are the ‘Line-in’ terminals and are to be connected with your radio/cassette
or CD player.
• All Caliber amplifiers have a variable input level adjustment. It allows you to match any signal source
(CD player, AM/FM cassettedeck, etc) correctly from its pre-amp output into your Caliber amplifier.
The adjustment ranges from 15V - 500mV(0.5V).
