699206
5
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
MANUAL RMD 801DAB-BT
3
Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against
metal parts. To avoid short-circuiting, cover all disconnected lead with insulating tape. There is a possibility of short-circuiting if the
leads are not insulated.
Route and secure all wiring so it cannot touch any moving parts, such as the gear lever and handbrake. Do not route wiring in places
that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short
circuiting to the vehicle’s body.
Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead’s insula-
tion and cause a very dangerous short.
Do not shorten any leads, if you do, the protection circuit may fail to work when it should.
Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The
current capacity of the lead will be exceeded, causing overheating.
Since a unique audio I/C circuit is employed, never wire so the speaker leads are directly grounded or the left and right - speaker
leads are common.
When this product’s source is switched ON, a control signal is outputted through the orange lead. Connect to an external power amp’s
system remote control or the car’s Auto-antenna relay control terminal (max. 300mA 12V DC). If the car features a glass antenna,
connect to the antenna booster power supply terminal.
When an external power amp is being used with this system, do not connect the orange lead to the amp’s power terminal. Such con-
nection could cause excessive current drain and a major malfunction. Refer to the relevant owner’s manual for details on connecting
the power amp and other units, then make the connections correctly.
Do not block any vents or heater panels, Blocking them will cause heat to build up and may result in fire.
Make sure that the unit has a good chassis ground. A good ground connection will eliminate most electrical noise. A good chassis
ground requires a tight connection to the vehicles metal chassis. The area around the ground connection should be clean, bare metal
without rust, paint, plastic or dirt for a good electrical connection.
If noise is still experienced when the motor of the vehicle accelerates, a choke should be placed in line with the power to the unit.
The installation company will know what is required.
When replacing the fuse(s) the replacement must be of the same amperage as shown on the fuse holder. Never replace a fuse with
another of a different value. If the fuse blows again please contact your instsallation company.
Double check that all wiring and connections are correct before re-connecting the battery and turning on the unit.
After completing the installation and before operating the unit, reconnect the battery, then press the (RES) button with a pointed object,
such as a ball-point pen to set to unit to it’s initial status. After pushing the button, wait a few seconds for the red light to flash.
SAFETY PRECAUTIONS
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Caliber RMD801DAB-BT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Caliber RMD801DAB-BT in de taal/talen: Engels als bijlage per email.

De handleiding is 2,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Caliber RMD801DAB-BT

Caliber RMD801DAB-BT Snelstart handleiding - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Polski, Svenska - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info