684202
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
33
4. Fitting and Changing the Gas Cylinder
Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator is in position and in good condition.
Carry out this check each time you  t the appliance to a gas cylinder (see  g. 1).
Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
Ensure the gas cylinder is  tted or changed in a well ventilated location preferably outdoors, away from any source of ignition such as
naked  ames, and away from other people.
Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.
If there is a leak on your appliance (smell of gas), extinguish all sources of ignition in the vicinity of the appliance. If you wish to check
for leaks on your appliance, use soapy water which is applied to the suspected area. A formation of bubbles will indicate a gas leak.
Check that all the connections are securely  tted and re-check with soapy water. If you cannot rectify the gas leak, do not use the
appliance. Contact your local CADAC stockist for assistance.
When changing a gas cylinder,  rst close the cylinder valve and then the appliance valve, making sure the  ame is extinguished and
unscrew the regulator. Re- t the regulator to a full cylinder following the same precautions as described above.
After the appliance has been fully assembled, perform a gas leak test before operating the appliance.
Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.
5. General Maintenance
There are no predetermined maintenance intervals for this appliance.
It is dangerous to use an appliance with a cracked or perished seal and/or hose. Inspect both seals and hose regularly and replace if
they are not in order before using the appliance.
If the appliance was in use it will be hot. Allow to cool suf ciently before attempting any maintenance.
CADAC Patio BBQ’s are  tted with spesi c CADAC jets to regulate the correct amount of gas. Should the hole in the Jet become
blocked this may result in a small  ame or no  ame at all. Do not attempt to clean the Jet with a pin or other such device as this may
damage the ori ce, which could make the appliance unsafe.
5.1. Replacing a Blocked Jet
Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder.
Remove the grill plates. Remove the  ame tamers to expose the burners. Remove the retaining screws of the affected burner.
Remove the affected burner by lifting it out of its location taking care not to damage the control valve whilst doing so. This will expose
the Jet.
Unscrew the blocked Jet with a suitable spanner and replace it with a new Jet. Do not use pliers on the Jet as they can cause damage,
making the Jet unusable or impossible to remove.
Do not over tighten as this may damage the Jet. To re-assemble, reverse the above procedure.
3. Using the appliance
Place the cylinder inside the cabinet in the space provided.
Use this appliance only on a  rm level surface.
Before use ensure that the drip cup/tray is in place.
Make sure the gas cylinder is correctly  tted to the appliance.
Ensure the cylinder control valve is in the open position.
To light the appliance using the automatic igniter, push in and turn the control knob in an
anti-clockwise direction until spring resistance is felt. Hold the knob in this position for
3 – 5 seconds to allow the gas to  ow and then turn the knob fully anti-clockwise to the
HIGH position. This will cause the automatic lighter to light the burner. Should the burner
not ignite the  rst time, turn the control knob to the OFF position and wait 5 minutes,
repeat the process until the burner ignites.
Note! All burners are  tted with an automatic igniter.
Cross lighting: To light the burners using cross lighting, light the left burner as described
above.
To light the remainder of the burners, simply turn their control knobs to the HIGH position
while ensuring that the lighting sequence is such that any burner to be lit up is directly
adjacent to a burner which is already burning.
Manual ignition: To light the burners manually,  rst remove the cast iron grill plate and
the de ector plate directly underneath it. Ignite a match or  relighter and position it next
to the left hand burner. Turn on the gas supply to that burner only by pushing the control
valve in and turning it in an anti-clockwise direction. This will ignite the burner. Once the
burner is ignited, carefully replace the de ector plate and cast iron grill plate. You will
now be able to light the remainder of the burners as described in ‘Cross lighting’ above.
Use the control knobs to adjust the individual burner  ame intensity to the desired level
by turning the knob anti-clockwise to decrease the  ame and clockwise to increase it (see
g.3).
After use,  rst close the valve on the gas cylinder. When the  ame is extinguished, close
the burner control valves on the appliance by turning control knobs fully clockwise.
Fig. 3
Fig. 3
GB
503-0604 LEV7 (98250-31, 98250-33, 98251-43) Cadac Entertainer 3 & 4 - User Manual (EU & SA).indd 3 08/09/2017 11:56:20
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cadac 98251 - Entertainer bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cadac 98251 - Entertainer in de taal/talen: Engels als bijlage per email.

De handleiding is 0,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Cadac 98251 - Entertainer

Cadac 98251 - Entertainer Gebruiksaanwijzing - Nederlands - 6 pagina's

Cadac 98251 - Entertainer Gebruiksaanwijzing - Deutsch - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info