532517
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
1. Do not mount either unit close to fireplace or expose to high temperatures.
2. Do not expose the Door Chime unit to direct sunlight or moisture.
3. Make sure that no naked flame sources, such as lighted candles, are placed on the unit.
4. The unit should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the unit.
5. CAUTION: Replace only with the same or equivalent type of battery that is recommended by the manufacturer.
6. CAUTION: Danger of explosion if battery is incorrectly installed or replaced.
7. CAUTION: This product is not suitable for people who suffer from epilepsy due to flashing light.
Model No. SX-209
Important
R&TTE
approved
Press the button on the Push Button unit once, it sends a wireless
signal to the Door Chime and will activate one of the following
functions:
a) Sound and Light: The Door chime will sound as well as the
Super Bright Light flashing to
maximize attention.
b) Light Only: The Super bright Light on the Door Chime
unit will flash.
c) Sound Only: Door Chime unit will sound.
The function selector is located at the back of the unit, press the
buttons to select the function to operate the chime unit
accordingly. For repeat sound, press the button again. Holding the
button in will NOT repeat the sound.
Door Chime Operation
It is located at the side of the item, slide the switch to adjust the light function as follows:
a) Sound Only
b) Strobe Light Only
c) Sound + Strobe Light
It is located at the back of item, press the button to adjust the sound volume goes up and down. There is a total
of 8 different sound volume levels set, 1=mute and 8 =max level, the door chime will start operating at sound
level 6 initially.
Volume
Control
The unit comes from the factory on a pre-set radio frequency digital
code. However, should your door chime activate intermittently for no
reason at all, it is possible that a similar unit is operating nearby on the
same frequency digital code. The encoded frequency of the Push Button
(transmitter) can be changed to avoid this problem. The Door Chime
unit is equipped with an advanced self-learning operation code ability
therefore no setting is needed.
Digital Code Set Up
1. Remove the back of the case from the Bell Push unit.
2. There are 4-position dipswitch marked 1,2,3 & 4. Use an screwdriver
to alter the dipswitch levers to the “On/Off” position, which can be
altered to achieve a total of sixteen (16) possible digital codes.
3. Select any combination on the Push Button. Press the Push Button,
the Door Chime unit will sound to indicate that new operation code
is registerd and memorized, and it will only work with it.
4. To re-set the operation code, simply remove the batteries from the Door Chime unit and rest for 30 seconds,
it will erase the memory. Re-insert the batteries into the Door Chime unit, it will give 2-beeps to indicate that
it is ready for new code registration. Press the Push Button to confirm the new code is working.
5. Test to ensure correct operation before final installation.
Push Button
Eg.
A. Push Button unit
Power
Consumption
: 1 x 3 volt Lithium battery (CR2032 - included)
: 7.0mA - ON
0.003mA - OFF
B. Door Chime unit
Power
Consumption
Operating Temperature
Operating Distance
Selectable Tone
Selectable Digital Code
: 2 x 1.5 volt alkaline batteries (“C”, UM2 & R14 - included)
: Sound Only-200mA, Strobe Light Only-200mA, Sound+Light-350mA / 0.3mA-Stand By
: -10C to +40C
: 100 metres (320 feet approx.) in open field
: Total eight (8) tones available
: Total sixteen (16) possible digital codes
Problem
Chime does not
sound but LED lights
on Push Button
Chime does not
sound plus no lights
on Push Button LED
Chime sounds
without Push Button
being pressed
Possible Causes
1. Units is out of range (max. range 100M)
2. Push Button and Chime units are not on
same digital code
1. Flat Push Button battery
2. Wrong polarity of battery in Push Button
A similar Wire Free Door Chime product is
operating nearby on the same frequency
digital code
Suggested Remedy
1. Operate the Chime unit within the
operation range (100M)
2. Re-set the digital code
(see Digital Code Set Up)
1. Change the battery
2. Re-insert battery as internal marking
in right polarity
Change the digital code
(see Digital Code Set Up)
Important: There are no serviceable parts in the unit, do not attempt to repair it.
Trouble Shooting & User Hints
Specification
Type R2 Device - device where the sound output is created by the initial operation of the control and where the
period of sound output continues for designed duration irrespective of condition of the control.
• Sound
• Strobe Light
• Sound +
Strobe Light
Light Option Control Button
Sound Volume Control Button
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Byron SX-209 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Byron SX-209 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info