497312
12
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
Page 9 of 44 pages
DVD7200BT ENGLISH
Installing the device
Note:
Please observe the following safety instructions for the connection of the device:
- Read the entire installation section before connecting the device.
-
Disconnect the negative pole of the vehicle battery for the duration of the installation.
- Observe the safety instructions by the vehicle manufacturer during this task.
- If you need to drill holes for the installation, make sure that no parts of the vehicle are
damaged.
- The cross section of the positive and negative cable may not be less than 2.5 mm².
- Do not connect any of the vehicle’s plugs and cables to the radio unless you have the
appropriate specialized knowledge of this process!
- Only use the supplied cable to connect the device.
- Depending on the build of your vehicle, the installation may deviate from this
description.
- We do not assume any liability for damages caused by faulty installations or
connections, nor any subsequent damages.
- We recommend that you have the device installed by a specialized company. Then
you will have created the prerequisites for a problem-free functioning of the device. If
at any point during the installation you are unsure that you can correctly connect the
device by yourself, contact a specialist. A faulty installation may cause damages to
the device and the vehicle electronics.
1) Remove the installation frame from the device with the aid of the disassembly key, by
sliding the disassembly keys into the provided openings on the right and left side of
the device, as described in Fig A.
2) Make sure that the protrusion on the disassembly key points away from the device
during the insertion (Fig C + Fig. B.) Afterwards, the frame can be slid down over the
device towards the rear.
3) Now slide the installation frame into the installation slot provided for the car radio.
4) Now attach the installation frame by bending the installation brackets towards the
outside with a screwdriver. The frame is properly installed when it can no longer be
pulled out, yet also keeps from sliding into the installation slot.
5) Now connect the cable set and the antenna to the vehicle’s electronics corresponding
to page 6.
6) Insert the device into the installation frame until the stop.
7) The device then audibly snaps into the frame. Attach the front frame and then insert
the operating unit.
Fig. C.
Fig. B.
Fig. A.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bullit DVD7200BT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bullit DVD7200BT in de taal/talen: Engels als bijlage per email.

De handleiding is 1,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info