697447
70
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
5
Operating and fault displays
MCM10
70
5.4 Operating and fault indications via the RC35
The operating and fault indications relating to all boilers
and the MCM10 module can be checked on the controller
with EMS BUS control. For an explanation of the displays
on the MCM10 module, see tab. 11. The meaning of all
other displays is given in the documentation of the
controller and boilers.
5, 6,
7, 8
Operation: no heat
demand to the boiler;
boiler operational.
Operation: heat
demand to the boiler;
boiler in operation.
Configuration:
communication
between this boiler
and MCM10 module.
Wait until the
configuration has
completed.
Operation: no boiler
connected.
Fault: boiler fault.
1)
Remove fault on the
boiler.
Configuration/
Fault: no
communication
between
MCM10 module and
this boiler, although it
is installed.
Check the
corresponding
connecting lead/
cable.
Remove boiler fault.
Replace
MCM10 module.
Fault: no
communication
between
MCM10 module and
boiler because it has
been deliberately
removed.
Carry out
configuration reset
(Æ chapter 4.3).
Fault: communication
error between
MCM10 module and
boiler.
1)
Check the
corresponding
connecting lead/
cable.
Replace
MCM10 module.
1) Another boiler will be enabled automatically in case of heat demand
LED Off On Flashing
No. Diagnosis Remedy Diagnosis Remedy Diagnosis Remedy
Tab. 10 Operating and fault displays
Display Description Remedy
5H Break in BUS communication. Display in case of less than 4 installed boilers.
Check the cable between the boiler and the MCM10 module for a possible break.
Check the cable for firm seating and contact.
Check whether this fault originates in a boiler (Æ boiler installation instructions).
Replace MCM10 module.
4U
4Y
Short circuit (4U) or contact break
(4Y).
Check flow temperature sensor and its lead.
Replace MCM10 module.
EF Internal electronics fault. If a fault is indicated by one of the boilers: replace burner control unit of the corresponding
boiler.
If the fault is not indicated by one of the boilers: replace MCM10 module.
8Y The external switching contact has
opened.
Check the cable of the external switching contact for a possible break.
Check whether the connecting plug is present.
Replace MCM10 module.
AE Jumper configuration fault. Check whether the jumper has been correctly set.
AU The calculated boiler water
temperature is not reached in time.
Check whether a sufficient number of boilers functions normally.
AY A fault has occurred on one or
several boilers.
Remedy the fault on the boiler concerned.
Tab. 11 Operating and fault indications via the RC35
70

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Buderus MCM10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Buderus MCM10 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info