729945
21
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
21 / 24
4. Wait until the indoor temperature is displayed on the base station.
NOTICE!For permanent operation, mains power supply is recommended. Alternatively a
power supply with batteries is also possible. Proceed as follows:
5. Remove the battery compartment cover.
6. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.
7. Replace the battery compartment cover.
8. Wait until the indoor temperature is displayed on the base station.
NOTICE!When switching from mains power supply to battery power supply or vice versa,
the power supply is being disabled for a short moment for technical reasons. In this process
all settings made previously, will be deleted.
Remote sensor
1. Remove the battery compartment cover.
2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.
3. Set the channel selector switch to the desired channel (1, 2 or 3).
NOTICE!This weather station can be operated with up to 3 remote sensors. Each remote
sensor being connected must be operated on a different channel. If only one remote sensor
is connected, it should be operated on channel 1.
4. Replace the battery compartment cover.
10 Automatic time setting
After the power supply was established, the clock will automatically search for the radio signal. This
will take approximately 3 to 8 minutes to finish this process.
If the radio signal is received correctly, the date and time will be set automatically and the radio control
signal icon turns on.
If the clock fails to receive the time signal, go ahead with the following steps:
1. Press and hold the DOWN button for approx. 2 seconds to re-initialize radio signal reception.
2. Is the device still not receiving the signal, the time must be set manually.
Read the detailed manual for more information about manual time and alarm time settings (see down-
load information on page 2).
11 Manual time setting and setiings for weather
information display
1. Press and hold MODE button for approx. 3 seconds to change to time setting mode.
2. Digits to be set are flashing.
3. Press UP or DOWN button to change the value.
4. Press MODE button to confirm and continue to the next setting.
5. Settings order: Year > Change day and month > Month > Day > Hours > Minutes > 12/24-hours
mode > Time zone > Language > Setting weather information display > Barometric pressure unit
hPa/inHG
6. Finally press the MODE button to save the settings and exit the setting mode.
12 Alarm setting
1. Press MODE button several times to select the desired alarm function: Alaram 1 (AL 1) or Alarm 2
(AL 2). The display switches to the preset alarm time.
2. Press and hold MODE button for approx. 3 seconds to enter the alarm time setting mode.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bresser 7007550 Meteo NBF Colour bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bresser 7007550 Meteo NBF Colour in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 4,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Bresser 7007550 Meteo NBF Colour

Bresser 7007550 Meteo NBF Colour Gebruiksaanwijzing - Français - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info