655617
6
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
6
OWNER'S MANUAL • PATH
OPERATION AND PROGRAMS
1. Insert the Safety key.
2. Press the POWER button. The monitor will turn on.
3. Select program with the SELECT button.
4. In the program PRO1 (Manual program), the
program window will display a track view. In the
program PRO2-8 (preset profile program), the
program window will display a profile view. Press
ENTER / SELECT to confirm your desired program.
5. In the programs PRO1 and PRO2-8, press +
/ - buttons to set up your desired time to do the
exercise. Press ENTER / SELECT to confirm your
setting value. Press START to begin. In the PRO1
program, set the incline and speed manually.
In PRO2-8, the incline and speed changes are
automatic. You can set the speed and incline of each
profile bar also manually during training.
MAINTENANCE
The equipment is safe to use only when periodically
maintained and inspected for faults and wear.
CAUTION! Do not attempt any servicing or
adjustment other than those described in this
manual. Any other servicing must be performed
by an authorized service representative. Check the
tightness of all fixing screws once a year. Do not
overtighten.
CLEANING AND LUBRICATING THE TREADMILL
FAILURE TO LUBRICATE YOUR TREADMILL MAY
INVALIDATE THE PRODUCT’S WARRANTY!
Wipe the treadmill surfaces, especially the
handlebars and console from dust with a damp
cloth or towel. Do not use solvents. Use a small
vacuum nozzle to carefully vacuum around all
visible components (belt, running deck, side rails
etc.). Also keep the area near the treadmill clean.
While in use, the treadmill gathers dust that may
cause problems in the operation of the equipment.
In average domestic use (a maximum of 60 minutes
a day), you should check the lubrication once a
month – however, lubricate the belt only if needed.
In more demanding use, the lubrication needs be
checked at shorter intervals. This is best done before
you begin a training session. Check the lubrication
as follows:
1. Ensure the treadmill is powered off! Step on
the treadmill belt .and stand steadily where you
normally run on the belt.
2. Take hold of the horizontal handlebar and push
the belt with your feet so that it slides back and
forth. The belt should move softly and evenly,
without a sound.
3. If you notice jerky movement or if the belt will
not slide check for lubrication by sliding your hand
under the belt.
Lubricate the running deck according to the
following instructions:
1. Attach the nozzle of the lubrication tube to the
T-Lube S container.
2. Lift the running deck and lock it.
3. Position the nozzle between the belt and the
board. Try to reach the spray as far into the center of
the running deck as possible.
4. Spray the lubricant for 2-3 seconds.
5. Lower the running deck into its normal position.
Use treadmill for your training session. Or allow the
treadmill to run for at least 5 minutes.
NOTE! Lubricate your treadmill only with T-Lube
S silicon lubricant. Contact your local Bremshey
distributor for further supplies of T-Lube or further
information on lubrication and maintenance.
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually
needed, provided
the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to
one side due to the user’s running style (e.g. more
weight on one foot). The alignment of the belt is
adjusted by turning the two bolts at the back of the
treadmill.
ALIGN THE BELT ACCORDING TO THE FOLLOWING
INSTRUCTIONS:
1.
Turn the power switch on and increase the
treadmill’s speed to 5 km/h (3 mph).
2. If the belt drifts to the left, turn the left
adjustment bolt 1/4 turn clockwise and the right
adjustment bolt 1/8 turn anti-clockwise. If the belt
drifts to the right, turn the right adjustment bolt 1/4
turn clockwise and the left adjustment bolt ¼ turn
anti-clockwise.
3. If the belt remains centered the adjustment is
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned. If the belt
is allowed run across to one side for long periods of
time the edges of the belt may be damaged and the
treadmill may not continue to operate correctly. Any
damage to the belt caused by the lack of necessary
adjustment will not be covered by the warranty.
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on
the rollers. In normal use, however, keep the belt
as loose as possible! The belt tension is adjusted by
turning the same screws as used for aligning the
running belt. If turning the screws will not effect the
belt tension, please contact your local Bremshey
dealer.
1. Increase the treadmill’s speed to 5 km/h (3 mph).
2. Turn both adjustment screws an equal amount, ¼
turn clockwise.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bremshey Treadline Path bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bremshey Treadline Path in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Zweeds, Fins als bijlage per email.

De handleiding is 1,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info