706402
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
ENGLISH
4 Connecting using the table stand
Remove the rubber mat from the underside of the
base (Figure 15).
Strip back the outer sheath of the cable by 75mm
(3 in) to expose the two inner sheathed wires.
Strip back the positive and negative wires to expose
10mm (3/8 in) of bare wire. If using multi-strand wire,
twist the strands to obtain a neat end.
Feed each wire through the appropriate hole in the
back of the base, observing the polarity coding
as indicated. The wires will follow a channel and
emerge in line with the side holes in the spring
terminals.
Press the ends of the terminals fully and push the
wire into the terminals. Then release the terminal
ends to clamp the wire.
Replace the rubber mat.
5 Fitting and connecting using the
wall bracket
WARNING!
Do not attach the speaker to the ceiling. Decide how
the cable is to be routed to the wall bracket on the
wall surface (from underneath only), chased into the
plasterwork, or inside hollow (drywall) construction.
If routing the cable inside the wall or in the plaster
layer, install it before xing the wall bracket in place
and leave 50mm (2 in) showing with the outer sheath
stripped back.
Take care to route the cable clear of where the
bracket xing screws will be. For example, if the
cable is chased into the plaster from above, omit the
centre xing screw.
If laying the cable on the wall surface,t the wall
bracket rst. Cable cannot be routed around the
support platform of the bracket when the cover is
in place. There is only one knock-out in the cover
as shown, so the cable must approach from this
direction.
Using a spirit level, offer the wall bracket to the wall
and mark out thexing holes.
Drill and plug the wall as appropriate to the type of
construction (screws and plugs not supplied).
If laying the cable on the wall surface from below,
remove the knock-out at the bottom of the bracket
cover to accommodate the cable.
Strip back the ends of the inner cores of the cable
to expose 10mm (3/8 in) of bare wire and neatly
twist if multi-strand. Connect the wires to the screw
terminals, observing the correct polarity as shown.
Remove the table stand base, following the
instructions in Section 3.1.
Slide the cover up the stem. Make sure the securing
clamp is clear of the stem aperture in the bracket
and push the end of the speaker stem fully into
the aperture. Tighten the two screws through the
securing clamp evenly using the Torx key supplied
until the slack is taken out of the t of the stem.
Check that the tapered ridge of the clamp engages
the groove in the stem. Do not over-tighten.
Slide the cover back down the stem and click into
place on the wall bracket.
5
Figure 15
Figure 16
+
+
+
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bowers Wilkins MT-60D - M1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bowers Wilkins MT-60D - M1 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info