7
Overview of Programmes a Refer to the table of consumption values on page 8 and notes on page 6.
Programmes °C max.
T
Additional functions; infor
Algod
ón/Algodãoü (Cottons)
D - 90 °C
7 kg/
4 kg*
Hard-wearing fabrics, heat-resistant fabrics made of cotton
or linen
ĈTurboPerfect*, ć÷EcoPerfect, S Fácil (Easy-Iron),
+ Prelav. (+ Prewash)
ā÷Antialergias (Antiallergy) D - 60 °C
Hard-wearing fabrics made of cotton or linen
ĈTurboPerfect*, ć÷EcoPerfect, S Fácil (Easy-Iron), Skin Care;
especially suitable for increased hygienic demands or particularly
sensitive skin on account of prolonged washing at a defined tem-
perature, with a higher water level and longer rinsing cycle
Sintéticos
(Easy-Care)
D - 60 °C
3 kg
Easy-care fabrics made of cotton, linen, synthetic fibres or
blended fabrics
ĈTurboPerfect, ć÷EcoPerfect, S Fácil (Easy-Iron), Skin Care
+ Prelav. (+ Prewash)
Mix D - 40 °C Fabrics made of cotton or easy-care fabrics
ĈTurboPerfect, ć÷EcoPerfect, S Fácil (Easy-Iron), Skin Care;
different types of laundry can be washed together
R. de cama
(Easy-Care plus)
D - 40 °C
Dark-coloured fabrics made of cotton and dark easy-care
fabrics
Ĉ TurboPerfect, ć EcoPerfect, S Fácil (Easy-Iron), Skin Care;
Reduced rinse and final spin cycle
Camisas/Blusas
(Shirt/Blouse)
D - 60 °C
2 kg
Non-iron shirts made of cotton, linen, synthetic fibres or
blended fabrics
Ĉ TurboPerfect, ć EcoPerfect, S Fácil (Easy-Iron), Skin Care ;
S(Easy-Iron): spin only, hang up dripping wet
Delicado/Sedac (Delicate/Silk) D - 40 °C
For delicate, washable fabrics, e.g. made of silk, satin, syn-
thetic fibres or blended fabrics (e.g. curtains)
ĈTurboPerfect, ć÷EcoPerfect, S Fácil (Easy-Iron), Skin Care;
No spin between rinse cycles
: / Lana/Lã (Wool) D - 40 °C
Handä or machine-washable fabrics made of wool or con-
taining wool
Particularly gentle wash programme to avoid shrinkage of laundry,
longer programme breaks (fabrics rest in the detergent solution)
Rápido 15' (SuperQuick 15’) D - 40 °C
Easy-care fabrics made of cotton, linen, synthetic fibres or
blended fabrics
Short programme, approx. 15 minutes, suitable for lightly soiled
laundry
$ Sport D - 40 °C Fabrics made from microfibre ĈTurboPerfect, ć÷EcoPerfect, S Fácil (Easy-Iron), Skin Care
WPlumas/Penas
(Down)
D - 40 °C 1 kg
Machine-washable down-filled clothing
(no cushions or duvets)
Ĉ TurboPerfect, ć EcoPerfect, Skin Care;
Wash large items individually, meter detergent sparingly a page 6.
Additional programmes 2(Rinse)/c Centrif. adicional (Spin), > (Empty)
* Reduced load for additional ĈT function.
As a short programme, Mix 40 °C, with a maximum spin speed, is ideal.
Programmes without pre-wash - add detergent to compartment II , programmes with pre-wash - distribute the detergent between compartments I and II .
9403 / 9000979213
*979213*
WAE2447XEE ...
Robert Bosch Hausgeräte GmbH
Carl-Wery-Str. 34
81739 München / Germany
8
Safety instructions
– Read the instruction manual and installation instructi
machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock – Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent children from
locking themselves in and risking their lives.
Danger of suffocation – Keep packaging, film and packaging parts out of the reach of children.
Risk of poisoning – Keep detergents and care products out of the reach of children.
Risk of explosion – Items of laundry pretreated with cleaning agents containing solvents, e.g. stain
remover / cleaning solvent may lead to an explosion after being loaded into the
washing machine.
Rinse items of laundry thoroughly by hand beforehand.
Risk of injury – The washing machine door can become very hot.
– Be careful when draining hot detergent solution.
– Do not climb onto the washing machine.
– Do not lean on the open washing machine door.
– Do not reach into the drum if it is still rotating.
– Be careful when opening the detergent drawer while the machine is in operation.
Consumption values depending on model
Programme Load Electricity** Water**
Programme
duration
**
Algod
ón/Algodão (Cottons) 20 °C
7 kg 0,31 kWh 72 l 2 ¾ h
Algod
ón/Algodão (Cottons) 40 °C
7 kg 0,85 kWh 72 l 2 ¾ h
Algod
ón/Algodão (Cottons) 60 °C
7 kg 1,21 kWh 72 l 2 ¾ h
Algod
ón/Algodão (Cottons) 90 °C
7 kg 2,01 kWh 77 l 3 h
Sintéticos
(Easy-Care)
40 °C
3 kg 0,64 kWh 56 l 1 ¾ h
Mix 40 °C
3 kg 0,46 kWh 36 l 1 ¼ h
Delicado/Seda (Delicate/Silk) 30 °C
2 kg 0,24 kWh 37 l ¾ h
: / Lana/Lá (Wool) 30 °C
2 kg 0,22 kWh 47 l ¾ h
Programme
Additional
function
Load
Annual energy
consumption
Annual water
consumption
Algod
ón/Algodão (Cottons) 40/60 °C ć EcoPerfect*
3,5/7 kg 165 kWh 10686 l
* Programme setting for testing and energy labelling in accordance with EU directive 2010/30/EU with cold water (15 ºC).
** The values
ature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional func-
tions.
9
Care
Before washing for th
Do not load any laundry into the machine. Turn on the tap. Add the following to compartment II :
– approx. 1 litre water
– detergent (dosage according
hardness)
Set the programme selector to
Sintéticos (Easy-Care) 60 °C and select Inicio/Pausa + Carga (Start/ Reload). At the
end of the programme, turn the programme selector to Stop (Off).
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Remove detergent and cleaning agent residue immediately.
– Do not clean with a jet of water.
Cleaning the detergent drawer and housing...
... if it contains detergent or fabric softener residues.
1. Pull the drawer out, press down the insert and fully remove the drawer from the housing.
2. To remove the insert: press the insert upwards from below with your finger.
3. Clean the detergent dispenser tray and insert with water and a brush and dry it. Also remove
any detergent or fabric softener residues in the housing.
4. Attach the insert and engage (connect the cylinder to the guide pin).
5. Push in the detergent drawer.
Leave the detergent drawer open so that any residual water can evaporate.
W
Wipe the
Rust stains - use chlorine-free cleaning agent, not steel wool.
Descaling Ensure there is no laundry in the machine
Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the
correct dosage of detergent is used.
Emergency release, e.g. in the event of a po
The programme continues to run when the power has been restored. However, if the laundry has to be removed, the
washing machine door can be opened as follows:
Risk of scalding.
The detergent solution and laundry may be hot. If possible, leave it to cool down.
Do not reach into the drum if it is still rotating.
Do not open the washing machine door if water can be seen through the glass.
1. Turn the programme selector to Stop (Off) and disconnect the mains plug.
2. Drain the detergent solution a page 10.
3. Pull the emergency release downwards with a tool and release.
Washing machine door can then be opened.
Information on the display panel depending on model
F: 16 Close the washing machine door properly; laundry may be caught.
F: 17 Open the tap completely, supply hose kinked or trapped;
Clean the filter a page 10 , Water pressure too low.
F: 18 Detergent solution a page 10 .
blocked; Clean the drainage hose at the siphon a page 10.
F: 21 Motor fault. Call customer services.
F: 23 Water in the base tub, appliance leaking. Call customer services.
– Risk of electric shock. Disconnect the mains plug.
– Risk of explosion. No solvents.
1
Maintenance
Detergent solution pump
Turn the programme selector to Stop (Off) and disconnect the mains
plug.
1. Open and remove the service flap.
2. For models with a drainage hose: Remove the drainage hose from
the retainer and pull it from the housing.Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Replace the sealing cap and place the drainage hose in the retainer.
2* For Carefully
until
full,
steps until all the detergent solution has completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean
the detergent solution pump must rotate).
5. Replace the pump cover and screw it tightly.
6. Place the service flap back on and close.
To
litre of water into compartment II and start the > (Empty) programme.
Drainage hose at the siphon
Turn the programme selector to
Stop (Off)
and disconnect the mains plug.
1. Loosen the hose clamp, carefully remove the drainage hose (residual
water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose
clamp.
Filter in the water suppl
Risk of electric shock
Do not immerse the HydroSafe safety device in water (contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select 2(Rinse)/cCentrif.
// > (Empty)).
3. Choose Inicio/ Pausa (Start /Reload).
approximately 40 seconds.
4. Turn the Stop (Off) .
Clean the filter:
1. Depending on model:
Disconnect the hose from the tap.
Clean the filter using a small brush.
and/or for Standard and Aqua-Secure models:
Remove the hose on the rear of the appliance,
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
– Risk of scalding.
Allow the detergent solution to cool down.
– Turn off the tap.
1
What to do if ...
ʑ
Water is leaking out. – Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
– Inicio /Pausa + Carga (Start /Reload) not selected?
– Tap not turned on?
– Filter blocked? Clean the filter a page 10 .
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Programme stopped? a page 4 .
– (without final spia page 3, 4.
– Can be opened by emergency release only? a page 9.
ʑ
Programme does not start. – Inicio /Pausa + Carga (Start /Reload) or (Finished in) time selected?
– Washing machine door closed?
– Childproof lock active? Deactivate a page 5 .
ʑ
Detergent solution is not
drained.
– (without final spia page 3, 4.
– Clean the detergent solution pump a page 10 .
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Unsatisfactory spin result.
Laundry wet/too damp.
– Not a fault - the unbalanced-load detection system has cancelled the spin cycle
because of uneven distribution of the laundry. Distribute small and large items of
laundry evenly inside the drum.
– S Fácil (Easy-iron) selected? a page 5.
– Selected speed too low? a page 5 .
ʑ
The programme duration
changes during the wash
cycle.
– Not a fault – the programme sequence is optimised for the particular wash process.
This may result in changes to the programme duration in the display field.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary a page 9 .
ʑ
Odour formation in the
washing machine.
– Run programme
Algod
ón/Algodão (Cottons) 90 °C without laundry. Use standard
detergent.
ʑ
Status display³1 (Wash)
flashes. Foam may be
coming out of the detergent
drawer.
– Too much detergent used? Mix 1 tablespoon of fabric softener with ½ litre of water
and pour into dispenser II (not for outdoor and down-filled textiles!).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and “wandering”
during the spin cycle.
– Are the appliance feet fixed? Secure the appliance feet a Installation instructions .
– Transportation safety devices removed?
Remove the transportation safety devices a Installation instructions .
ʑ
Noises
cycles.
– Clean detergent-solution pump a page 10.
ʑ
Display panel/indicator
lamps
operation.
– Power cut?
– Fuses triggered? Reset/change the fuse.
– If the fault occurs repeatedly, call customer services.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced load detection system adjusts imbalance by repeatedly
distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse cycle.
ʑ
Detergent residues on the
laundry.
– Occasionally, phosphate-free detergents contain water-insoluble residues.
– Use the 2(Rinse) /c Centrif. adicional (Spin) cycle or brush out the laundry after
washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Stop (Off) and remove the mains plug from the socket.
– Turn off the water supply and call customer services a Installation instructions.
en operating instructions
Washing machine
WAE2447XEE ...
