697117
6
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
Operating instructions
6 720 876 041 (2019/10)
6
Congratulations on purchasing this BOSCH appliance.
You have acquired a top-quality product, which will
give you a lot of enjoyment.
2 Operating instructions
2.1 Getting to know your appliance
This appliance is an electronically-regulated, pressurized continuous-
flow heater for decentrally supplying hot water.
The electronic continuous-flow heater heats the water as it flows through
the appliance. One or more taps can be supplied with warm water.
2.1.1 Operating element
1 Status display
2.2 Operating the appliance
2.2.1 Switching the appliance on and off
The continuous-flow heater switches on and heats the water when
the warm water tap is opened. It switches off again if the water tap
is closed.
The factory default setting for the warm water outflow temperature
is 55 °C.
Note: The electronic control unit senses the input water’s temperature
and rate of flow and automatically adjusts the power consumption in
order to obtain the set output water temperature (up to the power limit).
Increasing the water temperature
If the supply water temperature is low and the flow-rate is high, then it
may happen that the set output water temperature is not obtained
because the power limit is exceeded. This is signalled by rapid flashing of
the status display.
If this happens, then slightly close the warm water tap.
2.2.2 Status display
2.2.3 Startup after power failure
Open the warm water tap fully and allow water to flow until it is warm.
2.2.4 Using the appliance after switching off the water supply
Switch off the appliance (unscrew the fuse in the fusebox).
Open the warm water tap and keep it open until the air has been
completely forced out of the water pipe.
Switch the fuse back on again.
Open the warm water tap fully and allow water to flow for at least one
minute.
Only then (for safety reasons) will the appliance begin to heat.
The appliance is now ready to operate.
2.2.5 Winter operation
Note: It is possible in winter that the supply temperature of the water is
reduced and the required outlet temperature is no longer achieved.
Reduce the water flow at the tap until the desired water temperature
is reached.
3 Cleaning
Only wipe off the appliance using a moist cloth.
Do not use acidic or abrasive cleaning materials.
Do not use a steam cleaner.
4 Customer Service
We ask you to always provide the BOSCH serial number (SNR/TTNR) of
your appliance when calling in a customer service engineer. You will find
the numbers on the ratings plate on the inner side of the front flap.
LED Appliance status
Off Off
Lights green On
Flashes green (1/s) The set temperature is not obtained; the rate of
water flow is too high for appliance rating
(the appliance has reached the power limit).
See “A fault, what to do?”
Flashes green (2/s) Cold-water rinse-through phase
Flashes red See “A fault, what to do?”
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch Tronic 4000 - 18 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch Tronic 4000 - 18 in de taal/talen: Nederlands, Duits, Engels, Frans, Pools, Turks als bijlage per email.

De handleiding is 3,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info