533055
5
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
en Betrieb des Geräts unerlässlich, da sie das Eindringen von
Flüssigkeiten und Schmutz ins Geräteinnere verhindern.
Bauen Sie niemals die Achse des Gashahns aus (Abb. 8). Bei
einer Störung den kompletten Gashahn ersetzen.
Achtung!
Bringen Sie den Aufkleber mit der umgestellten Gasart in der
he des Typenschildes an.
en
Ú
Installation instructions
Safety precautions
Read the appliance instructions before installing and using.
The graphics in these Assembly instructions are given as a
guide only.
The manufacturer is exempt from all liability if this manual's
requirements are not complied with.
All operations relating to installation, regulation and
conversion to other gas types must be carried out by an
authorised installation engineer, respecting all applicable
regulations, standards and the specifications of the local gas
and electricity providers.
You are recommended to contact the Technical Assistance
Service to convert to another gas type.
Before you begin, turn off the appliance's electricity and gas
supply.
This appliance has been designed for home use only, not for
commercial or professional use. This appliance cannot be
installed on yachts or in caravans. The warranty will only be valid
if the appliance is used for the purpose for which it was
designed.
Before installing, check that local distribution conditions (gas
type and pressure) and the appliance's adjustment are
compatible (see table I). The appliance's adjustment conditions
are written on the label or the specifications plate.
This appliance can only be installed in a well-ventilated place in
accordance with existing regulations and ventilation
specifications. The appliance must not be connected to a
combustion product removal device.
The supply cable must be attached to the unit to prevent it from
touching hot parts of the oven or hob.
Appliances with electrical supply must be earthed.
Do not tamper with the appliance's interior. If necessary, call our
Technical Assistance Service.
Before installing
This appliance is class 3 type, according to the EN 30-1-1
regulation for gas appliances: built-in appliance.
The units next to the appliance must be made of non-flammable
materials. The laminated covering and glue for adhering it must
be heat resistant.
This appliance cannot be installed above fridges, washing
machines, dishwashers or similar.
An oven must have forced ventilation to install a hob above it.
Check the dimensions of the oven in the installation manual.
If an extractor fan is installed, you must follow the installation
manual's instructions, always keeping a minimum distance of
650 mm to the hob.
Preparation of the kitchen unit (fig. 1-2)
Make an appropriate size cut in the worktop surface, depending
on the installation method. standard (a) or flush (b). For flush
installation:
All cuts in the worktop surface should be done by a
specialised shop.
The cuts should be clean and precise, as the cut edge is on
the surface. The stability of the furniture should also be
ensured after cutting work.
Use only specially designed work surfaces, resistant to high-
temperature and water (e.g. natural stone or tiled).
Surrounding furniture must be resistant to temperatures up to
90 °C.
If the hob is electric or mixed (gas and electricity) and there is
no oven below, place a non-flammable separator (e.g. metal or
plywood) 10 mm from the bottom of the hob. This will prevent
access to the base of the hob.If the hob is gas, it is
recommendable to place the separator at the same distance.
On wood work surfaces, varnish the cutting surfaces with a
special glue. This protects them from moisture which could
collect under the work surface.
Installation of appliance
A) Standard installation (fig. 3a)
Depending on the model, the adhesive seal may be factory-
fitted. If this is the case, it should not be removed under any
circumstances, since the adhesive seal prevents leaks. If the
seal has not been factory-fitted, apply it to the underside of the
hob.
Fitting the appliance onto the kitchen unit:
1. Remove the clips from the accessory bag and screw them into
the position indicated so that they can turn freely.
2. Insert and centre the hob.
Press the sides of the hob until it is supported around its entire
perimeter.
3. Turn the clips and tighten them fully.
The position of the clips depends on how thick the work
surface is.
B) Flush installation (fig. 3b)
1. Complete a normal installation of the appliance making sure
that it is surrounded by a uniform slot. The hob surface should
be slightly below the work surface.
For tile worktops, if necessary, raise the bearing surfaces with
strips resistant to water and temperatures.
2. Check the operation and position of appliance.
3. Fill the gap between the worktop and hob with conventional
silicone adhesive appropriate in the colour you desire.
Note: If unsuitable silicone adhesive is used on natural stone
surfaces then this can produce colours that can not be
removed. Our Technical Assistance Service can provide you
with the most suitable glue (code 310818). Please note the
manufacturers instructions for use.
4. Smooth the silicone adhesive with a scraper or wet finger
moistened with soap and water before it forms a layer.
5. Allow the silicone adhesive to dry before using the appliance.
Removal of hob
Turn off the appliance's electricity and gas supply.
Unscrew the clips and proceed in the reverse order to
installation.
Gas connection (fig. 4)
The end of the inlet connection point of the gas hob has a 1/2”
(20.955 mm) thread that allows for:
fixed connection.
connection using a flexible metal pipe (L min. 1 m -
max. 3 m).
The watertight seal (034308) supplied must be inserted
between the manifold outlet and the gas supply.
You must prevent the pipe from coming into contact with
moving parts of the kitchen unit (for example, a drawer) and
prevent access to any spaces which might become obstructed.
Do not move the L-tube from the factory-fitted position,
regardless of the connection type.
If you need to make a cylindrical connection, replace the factory-
fitted L-tube with the one in the accessory bag. Fig. 4a.
Please remember to insert the seal.
: Danger of leaks!
If any connection is handled, check the seal.
The manufacturer is not liable for any connection leaking, after
being handled.
Electric connection (fig. 5)
Check that the voltage and power of the appliance are
compatible with the electrical installation.
The hobs are supplied with a power cable with or without a wall
socket plug.
Appliances with plugs must only be connected to sockets that
have earth wires correctly installed.
Provide an omnipolar cut-off switch with a minimum contact
opening of 3 mm (except for plug connections, if the user has
access to it).
This appliance is type “Y: the supply cable can only be
changed by the Technical Assistance Service and not the user.
The cable type and minimum cross-section must be respected.
Changing the gas type
If the country's regulations allow, this appliance can be adapted
to other types of gas (see specifications plate). The components
required for this are in the transformation kit supplied
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PPS816C91N bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PPS816C91N in de taal/talen: Duits, Italiaans, Portugees, Spaans, Pools, Turks als bijlage per email.

De handleiding is 1,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Bosch PPS816C91N

Bosch PPS816C91N Gebruiksaanwijzing - Nederlands - 17 pagina's

Bosch PPS816C91N Gebruiksaanwijzing - English - 10 pagina's

Bosch PPS816C91N Gebruiksaanwijzing - Français - 17 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info