708261
16
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
16 | English
1 609 92A 1PU | (13.11.15) Bosch Power Tools
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory loosen the screw
7 with the hex key 8 and remove the tool.
Mount the application tool/accessory (e.g. plunge cut saw
blade 6) in such a way on the tool holder 5 that the openings
of the tool engage into the cams of the tool holder.
For a safe and fatigue-free working position it is possible to
position the application tools/accessories in any snap-in posi-
tions on the tool holder. Position the tool in such a way that
the depressed centre points downwards (marking on the tool
is readable from above, see figure on the graphics page).
Use the screw 7 to fasten the application tool/accessory.
Tightly fasten the screw 7 with the hex key 8.
Check the tight seating of the application tool/accesso-
ry. Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
hazard.
Mounting and Adjusting the Depth Stop
The depth stop 11 can be used when working with segment
saw blades, Riff-segment saw blades and segment blades.
If required, remove an already mounted application tool/ac-
cessory.
Slide the depth stop 11 over and beyond the tool holder 5 to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
(see indication on the depth stop in large font and not in
brackets).
With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Insert the appropriate segment saw blade for the desired cut-
ting depth. Slide the depth stop 11 from the tool holder 5 in
the direction of the application tool until you can rotate it free-
ly. Rotate the depth stop 11 so that the desired cutting depth
is above the section of the saw blade, which will be used to
saw. Slide the depth stop 11 once again to the stop onto the
gear head of the application tool.
For all other cutting depths and when working with other appli-
cation tools, remove the depth stop 11. For this, remove the
application tool and pull the depth stop from the gear head.
Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate 9 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 10, free the Velcro back-
ing of the sanding plate 9 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 10 flush alongside one edge of the
sanding plate 9, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 10, grasp it at one of the tips and
pull it off from the sanding plate 9.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
BIM plunge cut saw
blades, metal
Metal (e. g. unhardened nails,
screws, smaller profiles),
non-ferrous metals
Smaller separating and plunge cuts;
example: shortening narrow profiles, cutting fastening
elements such as staples
HM-Riff segment
saw blade
Grouting joints, soft wall tiles,
glass-fibre reinforces plastic
and other abrasive materials
Cutting and separating close to edges, in corners or hard
to reach areas;
example: removing grouting joints between wall tiles for
repair work, cutting openings in tiles, gypsum boards or
plastic
HM-Riff delta plate
Mortar, concrete remainders,
wood, abrasive materials
Rasping and sanding on hard surfaces;
example: removing mortar or tile adhesive (e.g. when
replacing damaged tiles)
Scraper, rigid
Carpets, coverings Scraping on hard surfaces;
example: removing carpet and tile adhesive
BIM serrated seg-
ment saw blade
Insulation material, insulation
panels, floor panels, sound in-
sulation panels, cardboard,
carpet, rubber, leather
Cutting soft materials
Accessory Material Application
OBJ_BUCH-2516-002.book Page 16 Friday, November 13, 2015 9:25 AM
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PMF 1800 E Multitool bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PMF 1800 E Multitool in de taal/talen: Frans als bijlage per email.

De handleiding is 3,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info