78621
10
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
English - 5
The SDS-plus tool holder can easily be replaced
by the keyless chuck supplied with the machine.
The keyless chuck serves for rapid insertion of
the tools without the SDS-plus (e. g. round shaft
drill, screwdriver bits).
Do not hold the machine by the chuck!
Removal
Danger of injury! Before removing the
chuck, make sure to remove the tools or
bits.
Tightly grip the chuck locking ring 3 and pull
strongly in the direction of the arrow. Remove the
chuck.
Mounting
Using the whole hand, tightly grip the chuck.
Twist it onto the taper shaft of the chuck until it is
clearly heard to latch. The chuck automatically
locks.
Check the locking function by pulling at the
chuck.
Tools with a cylindrical shaft can be clamped us-
ing the keyless chuck.
The keyless chuck is not suitable for
hammer drilling.
Mounting the Keyless Chuck
Remove the SDS-plus tool holder. Mount the
keyless chuck in the same way as the SDS-plus
tool holder.
Open the Keyless Chuck
(see figure )
Loosen chuck by turning the interlock 15 clock-
wise .
Open chuck by turning it counter-clockwise.
Clamping the Tool
Insert the tool and manually close chuck while
holding knurled ring 16.
Lock chuck by turning interlock 15 counter-clock-
wise .
Set the impact stop switch 5 to “Drill”.
Removing the Keyless Chuck
Tightly grip the chuck locking ring 3 and pull it
strongly in the direction of the arrow.
Tool inserts with cylindrical shank can be
clamped with the key type drill chuck (accessory)
and the corresponding adapter (accessory).
Set the impact stop switch 5 to “Drill-
ing” (only at a standstill).
Clean and lightly grease the adapter shank.
Insert the assembled chuck with a twisting man-
ner into the tool holder until it latches. The chuck
locks itself. Check the locking by pulling on the
chuck.
The machine is also suitable for occasional
screwdriving applications, however, not for
screwdriving applications with extreme re-
ductions of speed at which the overload
clutch frequently responds.
For screwdriving, the universal bit holder with
SDS-plus shank (accessory) must be used.
Set the impact stop switch 5 to “Drill”.
Set the direction of rotation to right-hand rota-
tion.
Regulate the speed with the On/Off switch 7.
Change the SDS-plus
Tool Holder (GBH 24 VFR)
Keyless Chuck for Tools with a
Cylindrical Shaft (GBH 24 VFR)
3
Key Type Drill Chuck for Tool
Inserts with Cylindrical Shank
(GBH 24 VRE)
Screwdriving (see figure )
E
G
17 • 1 619 929 589 • TMS • 08.08.02
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GBH 24,0 VRE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GBH 24,0 VRE in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info