71902
56
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
56
Electrical connection
The installation of this appliance and the connection to the electrical network should be entrus-
ted only to an electrician perfectly to the fact of the normative regulations and which respects
them scrupulously.
Protection against the parts under tension must be ensured after the builting-in.
The data of connection necessary are on the stickers place on the hob casing near the con
-
nection box.
The connection to the main must be made using an earthed plug or via an omnipolar circuit
breaking device with a contact opening of at least 3 mm.
The electrical circuit must be separated from the network by adapted devices, for example :
circuit breakers, fuses or contactors.
Caution !
This appliance has only to be connected to a network 230 V~ 50 Hz. Connect always the earth
wire. Respect the connection diagram. The connection box is located underneath at the back of
the hob casing. To open the cover use a medium screwdriver. Place it in the slits and open the
cover.
(*) calculated with the simultaneous factor following standard TN 60 335-2-6/1990.
Connecting the cooktop:
For the various connections use the brass bridges which are in the terminal box.
1 phase 23 0V~1F+N (not for the Netherlands!):
Place a bridge between 1 and 2 then between 4 and 5. Attach the earthing to the earth” terminal
clamp, the neutral N to terminal clamp 4 or 5, and phase L to terminal clamp 1 or 2.
2 phases 400V~2F+N:
Place a bridge between 4 and 5. Attach the earthing to the “earth” terminal clamp, the neutral N
to terminal clamp 4 or 5, phase L1 to terminal clamp 1 and phase L2 to terminal clamp 2.
2 phases 23 0V~2F+2N:
Place a bridge between 2 and 3. Connect the earthing to the “earth” terminal clamp, neutral N1 to
terminal clamp 4, neutral N2 to terminal clamp 5, phase L1 to clamp 1 and phase L2 to clamp 2.
Caution ! ensure that you : correctly attach the wires and the bridges. Tighten the screws properly.
Before making the connection, we strongly advise you to locate the phase(s), neutral and earth on
the mains. If you have any doubts, call your electrician. Note: the bridges between terminals 4-5
and between terminals 1-2 were installed during the factory check. We cannot be held responsible
for any incident resulting from incorrect connection or which could arise from the use of an ap-
pliance which has not been earthed or has been equipped with a faulty earth connection.
Mains Connection Cable diameter Protection calibre
230V~1P+N 50Hz 1 Phase + N 3 x 2.5 mm² 25 A *
400V~2P+N 50Hz 2 Phases + N 4 x 1.5 mm² 16 A *
230V~2P+2N 50 Hz 2 Phases + 2N 5 x 1,5 mm² 16 A *
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Boretti BIK 70 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Boretti BIK 70 in de taal/talen: Nederlands, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Boretti BIK 70

Boretti BIK 70 Gebruiksaanwijzing - Nederlands, English, Français, Espanõl - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info