775469
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
About this product
A small ANT+ and Bluetooth wireless remote that’s easy to pair and makes on-bar control of bicycle lights a
breeze. The versatile remote mounts to both road or MTB bars and can be paired with up to 4 lights.
IMPORTANT: To use the Transmitr MicroRemote, you must have ANT+ compatible lights mounted on your
bicycle.
Compatible Bontrager lights:
Ion Pro RT
Ion 200 RT
Ion 450 RT
Flare RT
Ion 800 RT
Ion 700 RT
Ion 350 RT
Other ANT+ compatible lights
To set up any other light, please refer to the manual that came with your light.
Before you start
There are two phases to this installation: pairing the lights to the remote and attaching the lights and remote
to the bike. It is easiest to pair the lights to the remote before attaching it to the bike.
LED
Quick Mount CR1632
Battery
Bontrager
Transmitr MicroRemote
www.bontrager.com
Change front light control mode
Hold down the button for 8 seconds. If you release the button between 8 and 15 seconds, the remote will
switch to the new control mode. It will flash to indicate which mode the remote is in: Red = High Mode
Control; Green = Mode Selection.
NOTE: If you do not release the button before 15 seconds, the remote will enter pairing mode.
Rear lights
The default setting is LOW. To change the saved mode, turn on the light. Use the button on the rear lights
to change the mode, then turn off the system using the remote.
Can’t find light
If you are attempting to interact with a light and the remote can’t find it, the remote will flash red for 2
seconds. And you must repeat the pairing process.
Low battery
If the battery on one of your lights has fallen below 5%, the remote lights up solid red for 2 seconds. This
will happen only when turning the system on, or turning the system off.
Battery activation
1. Twist anticlockwise to open the
remote. Keep the top half
assembled.
2. Pull out the battery activation
tab.
3. Twist the remote clockwise to
close.
A note about pairing
Up to four ANT+ compatible lights can be paired to the Transmitr MicroRemote in a single pairing session.
Once in pairing mode, the remote will automatically search for each activated light, to pair one at a time, in
sequence. The pairing process is the same for all ANT+ compatible lights, regardless of whether it’s a front
light or a rear light.
NOTE: All lights must be paired in the same continuous procedure. If you choose to add a light later, you
will need to pair each light again at that time.
Pairing
1. Before starting, place the remote and all lights within 15cm (6 inches)
of each other.
PN 597194
NOTE: Move 4.5 metres (15 feet) from other ANT+ compatible lights to prevent accidental pairing.
2. For all lights you wish to pair, turn on each light then quickly turn it off again.
NOTE: After completing this step, do not press the power button on the light again until pairing is complete.
3. Press and hold the button on the remote for at least 15 seconds. Position your thumb on the remote
button so you can see the red light flash under the button. Release the button when the green/red light
begins to flash.
NOTES: Upon entering the pairing process, all previously stored pairing is removed.
If a light is accidentally paired, start the pairing process again.
4. While the remote searches for a light, the LED flashes red. When the remote finds a light, the LED will
change from a red flash to a green flash and the found light will turn on.
5. While the remote is still flashing green, single-press the button on the remote. The LED will begin flashing
red again to find another available light to confirm you have paired the correct light.
6. Repeat steps 4 and 5 for each light to pair.
7. To exit pairing, single-press the button while the remote is flashing red. If pairing to 4 lights, the remote
will exit pairing mode automatically after the fourth light is paired.
NOTE: Waiting at any time for 10 seconds will also end the pairing process automatically.
Verify pairing
1. Double-click the remote button to turn on all paired lights.
2. Press and hold the remote button for 1 second to turn off the light(s).
Remote operation with paired lights
When the Transmitr MicroRemote is used while lights are being used in auto mode with a Garmin, the
remote will take over changing the mode to individual on the Garmin. If a user wants auto mode to function
again, they’ll need to select it again on the Garmin.
The remote will recognise available lights within 30m (100ft) as long as there is a clean line of sight.
All lights will require a double-click to turn on.
Once on, a single-click will change the mode of the front light, depending on the light type. A long press
will turn the lights off if they are on.
The front light will operate in two configurations: High Mode Control or Mode Selection. The default out-
of-the-box experience is High Mode Control.
The rear lights will only turn on and off.
Front light configurations
Each light will turn on to the last mode it was in when the remote turned the light off.
High mode control
If there is no saved mode, the light will turn on to LOW. Subsequent button presses will alternate the light
between HIGH and the previous mode.
Mode selection
By default, if there is no saved state, the lights will turn on to LOW. After this, each button press will
advance the lights through the mode list.
Example: High (click) -> Medium (click) -> Low (click) -> Night Flash (click) -> Day Flash
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bontrager Transmitr MicroRemote bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bontrager Transmitr MicroRemote in de taal/talen: Engels als bijlage per email.

De handleiding is 0.38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info