626831
14
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
12
SECTION 7: TROUBLESHOOTING
While we don’t expect you to have any problems with your blender, sometimes
failures do occur� Use the following guidelines to see if the problem is easily fixed
or requires service�
7.1 BLENDER MOTOR WILL NOT TURN ON (NO POWER)
If the blender motor will not turn on, try the following:
1� Determine if the Liquid Crystal Display (LCD) is lit� An absence of a lit LCD
indicates a lack of power to the unit
2� Make sure the main power switch on the back lower-right corner is turned on�
(On is indicated by the vertical slash (I) on the power switch)�
3Check your house circuit breaker switch to make sure it is set to the ON position�
4� Unplug the power cord from the wall receptacle, wait 5 seconds, then plug power
cord back in
7.2 ERROR MESSAGES ON DISPLAY
Overload: This message indicates an overload on the motor� Turn off and unplug
the unit� Remove the blender jar from the motor base, and turn the shaft by hand
to ensure the blade turns freely� If the blade does not move freely, check for any
obstruction in the jar� If the blade moves freely, plug in the unit and turn the
blender on� If the overload condition reoccurs, please contact your Blendtec
Service Agent for further assistance�
Overtemp: This message indicates that the motor is overheating� The blender has
been disabled until the unit cools to operating temperature� Turn off and unplug
the unit� Allow it to cool for at least 20 minutes�
E-05 (Reset Error): This message indicates a permanent failure of the electronics
in the unit� Please contact your Blendtec Service Agent for repair/replacement (see
Section 8: Warranty)�
E-04 (No Zero Crossing): This message indicates failure of a component on the
electronic board� Please contact your Blendtec Service Agent for repair/
replacement (see Section 8: Warranty)�
7.3 NOISE LEVEL CHANGES
If the blender noise level has increased from original levels, determine whether
the sound is coming from the blender motor or jar
1� Blender motor: Remove the jar, and press Pulse �Listen to the motor� If it is
excessively noisy, please contact your Blendtec Service Agent for evaluation�
2� Jar: After checking the motor, fill the jar with 2 cups of water and place back on the
motor base� Run the blender for a few seconds by pressing the Pulse
button
If you have more than one jar, test a different jar to determine whether the sound is
different� If a jar is excessively noisy, or if the blade assembly seems loose or sounds
gravelly when turned by hand, please contact a Blendtec Service Agent�
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blendtec CLASSIC 560 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blendtec CLASSIC 560 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Blendtec CLASSIC 560

Blendtec CLASSIC 560 Gebruiksaanwijzing - Français - 11 pagina's

Blendtec CLASSIC 560 Gebruiksaanwijzing - Espanõl - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info