626841
5
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
76
If installing more than one blender, allow 14”–16” (356 - 406 cm) of center-to-center
blender spacing�
If installing a sound enclosure, allow a clearance of at least 5 ½” (14 cm) from the
sound enclosure to the wall and 26” (66 cm) from the countertop to any over-the-
counter cabinetry�
Ensure lower cabinetry allows adequate airflow�
The blender draws ambient air into the vent holes located on the lower back of
the motor and then evacuates hot air through the vents located on the lower front
and sides of the motor� For the motor to cool properly, a sufficient amount of air
must be able to circulate around the motor�
There should be at least 6 ½” (165 cm) of space from the countertop to the
next lower shelf of the cabinet, leaving a minimum space of 3” (76 cm) between
the bottom of the motor and the lower shelf� Cabinetry should not be closed; it
should allow air to flow freely from the outside to the inside of the cabinet space�
Plastic bags, cups, and so forth, should not be stored closer than 3” (76 cm) from
the bottom of the motor�
Cut a hole in the countertop 4 ⅜“ (11�1 cm) wide and 5 ⅞” (14�9 cm) long (see the
countertop hole template in Appendix A)� Ensure that the 4 ⅜” (11�1 cm) sides are
parallel with the machine operator
Note: Double check to ensure that all space requirements and measurements
are correct BEFORE cutting.
In-Counter Installation
Feed the electrical cord through the hole in the countertop�
Gently place the blender unit into the hole
Ensure the gasket is seated correctly, lying flat against the counter surface and
not pinched by the housing�
Plug the unit into an outlet with appropriate electrical protection
Figure 3. Stealth In-Counter Clearance
3” (7.6 cm)
Minimum
clearance
¾” (1.9 cm)
Maximum
thickness
4.1.2 Stealth 875™ Quick Start Guide
1Touch the power icon to turn on the blender�
2� Raise the sound enclosure lid
3� Place the blender jar on the motor base, ensuring the jar is completely seated
and the jar lid is secured
4� Close the sound enclosure lid
5� On the control surface, touch the desired blend cycle number, pulse icon or
desired location on the slider control bar�
6� To stop a blend cycle before the programmed time elapses, press the
cancel/exit button� If you have enabled the Blend Cycle Pause feature, press
the previously selected blend cycle button to pause the cycle� To resume
the paused cycle, press the previously selected blend cycle button again
4.1.3 Stealth 885™ Quick Start Guide
1Press the power icon to turn on the blender�
2� Raise the sound enclosure lid
3� Place the blender jar on the motor base, ensuring the jar is completely seated
and the jar lid is secured
4� Close the sound enclosure lid
5� On the control surface, press the desired blend cycle number or pulse icon
6� To stop a blend cycle before the programmed time elapses, press the
cancel/exit button� If you have enabled the Blend Cycle Pause feature, press
the previously selected blend cycle button to pause the cycle� To resume
the paused cycle, press the previously selected blend cycle button again
4.1.4 Automatic Cycle Operation
Your Stealth blender is preprogrammed with multiple blender profiles to help
operators achieve consistent blends with a minimum of training, trial, and error�
You can select from the following profiles and blend cycles:
Scroll (visible in programming mode)
Power Cancel/Exit
Mode
Slider Control Bar
Preprogrammed Cycle Buttons
Pulse
Select (visible in programming mode)
Scroll
Power
Cancel/Exit
Preprogrammed Cycle Buttons
Pulse
Select
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blendtec CHEF 775 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blendtec CHEF 775 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Blendtec CHEF 775

Blendtec CHEF 775 Gebruiksaanwijzing - English, Français, Espanõl - 156 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info