167456
4
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
4
terminal of the battery. Scratch the surface down to the bare met-
al at the point at which the earth contact is made and apply graph-
ite grease.
Connection examples
Connecting the voltage supply ................................................... Fig. 2
Connection to car radios with RCA output ................................. Fig. 3
Connection to car radios with loudspeaker output ..................Fig. 3 *
Loudspeaker connections .......................................................... Fig. 4
Connecting the wire remote control (REMOTE GAIN) .............. Fig. 5
The switching line must be connected when connection is carried out
using the RCA jacks or the loudspeaker jacks of the car radio.
+12V
LEVEL control
You can use the LEVEL control to adjust the input sensitivity of the
Velocity power amplifier to the output voltage of your car radio’s preamp
output.
The setting can be adjusted between 0.2 V and 5 V.
When connecting a car radio produced by another manufacturer, you
must adjust the input sensitivity in accordance with the information
provided by the manufacturer.
Please note that the LEVEL control is not a control for adjusting the
volume!
REMOTE GAIN
Connection for the supplied wire remote control (5 m).
This gives you the convenience of controlling the bass level remotely
(see Fig. 5).
If you want to use the remote control, the device must be operat-
ed with the low-pass filter activated (crossover switch set to po-
sition LP).
INPUT
Preamp inputs for the right and left channels. Please use high-quality
Velocity RCA cables for this connection.
OUTPUT
Outputs for connecting an additional amplifier (formation of chains of
amplifiers). Please also use high-quality Velocity RCA cables for this
connection.
LP / HP / FULL switch
Before installing, adjust the crossover switch on the power amplifier to
set the low pass filter (LP), high pass filter (HP) or full range (FULL). If
you select the FULL position, the full frequency response will be used
at the output.
Using the integrated crossovers is particularly useful in the case of
multi-channel sound systems with a separate subwoofer.
In order to obtain the best sound when a subwoofer is connected, the
subwoofer must be separated as far as the frequencies it receives are
concerned, i.e. it must only be fed with low frequencies (bass).
To ensure that this is the case, select LP and use the crossover fre-
quency control to adjust the upper frequency to between 50 Hz and
250 Hz. This ensures that every subwoofer is optimally separated as
far as the frequencies it receives are concerned.
If HP is selected, you can use the associated crossover frequency
control to adjust the lower cut-off frequency to between 50 Hz and
250 Hz.
If you want to precisely optimise the acoustic settings of the crosso-
ver, we recommend you obtain advice from a Velocity dealer.
It is very important that you take into account the specifications
of the loudspeakers being used whilst you are adjusting the cross-
over.
Crossover frequency control (LOW PASS + HIGH PASS)
If the crossover is activated (LP or HP) by adjusting the position of the
crossover switch, you can then use the corresponding control to ad-
just the crossover frequency of the respective filter to anywhere be-
tween 50 Hz and 250 Hz or 50 Hz and 250 Hz (i.e. continuously vari-
able setting). This control has no function in full range mode.
Settings for a subwoofer
In order to obtain the best sound when a subwoofer is connected, the
subwoofer must be separated as far as the frequencies it receives are
concerned, i.e. it must only be fed with low frequencies (bass).
1. Firstly, turn down the LEVEL control on the amplifier to minimum
and set the LOW PASS frequency control to its centre position.
2. Now play some music on your car sound system that you are very
familiar with and that contains some low bass (e.g. pop music).
Now slowly increase the volume of the subwoofer by turning the
LEVEL control on the amplifier in a clockwise direction until you
feel that the sound of the music is well balanced, i.e. the bass is
neither too weak nor overpowering.
3. Now listen to the relationship between deep male voices and the
upper bass and also take note of the relationship between the up-
per bass (kick bass) and the lower bass. The bass should ideally
sound crisp and have a clear low bass component, and male voic-
es should neither sound too weak nor should they billow out. You
can stop making adjustments if you are happy with the sound. If
not, move on to steps 4 and 5.
4. If male voices seem to billow out or the low bass is too weak, you
should turn the LOW PASS frequency control slightly towards min-
imum and then continue making your adjustments as described in
point 2 onwards.
5. If the bass sounds low but dirty and booming or the male voices
sound too weak, you should turn the LOW PASS frequency control
slightly towards maximum. Next, continue making your adjustments
as described in point 2 onwards.
6. The phase control should be set in such a way that the bass blends
into the overall sound as best as possible and cannot be heard as
a separate sound source.
If you want to precisely optimise the acoustic settings of the crosso-
ver, we recommend you obtain advice from a Blaupunkt dealer.
It is very important that you take into account the specifications
of the loudspeakers being used whilst you are adjusting the cross-
over.
BASS BOOST
You can adjust the bass output of the Blaupunkt amplifier using the
bass boost control. The settings range covers 0 dB to 0-12 dB.
SUB SONIC
The subsonic filter is used when a subwoofer is connected to the am-
plifier. It can be adjusted in order to protect the subwoofer against
mechanical overload due to low bass frequencies that fall outside our
hearing range.
Integrated fuses (FUSE)
The fuses that are integrated in the amplifier protect the power ampli-
fier and the entire electrical system in the event of a fault. If the fuse
needs to be replaced, never bypass/bridge the fuse and never replace
it with fuse types that are designed for higher currents.
Power-on indicator (POWER / PROTECTION)
Green light: Power amplifier switched on, normal operating mode.
Red light: Power amplifier has been electronically deactivated due
to a fault.
Subject to changes.
Introduction (F)
Toutes nos félicitations pour l’achat de cet amplificateur car audio de
haute qualité
En tant que créateur d’innovations dans le domaine de la hi-fi embar-
quée, nous vous offrons avec nos nouveaux amplificateurs VPA (clas-
se A/B) l’accès au monde audiophile de haut niveau.
Leurs réserves de puissance extrêmement élevées et leur son excep-
tionnel font des nouveaux amplificateurs Blaupunkt des séries Veloci-
ty de véritables merveilles sonores quant à la reproduction musicale «
live » en voiture. Offrant un rapport signal / bruit supérieur à 100 dB,
un facteur de distorsion harmonique extrêmement faible, un très haut
facteur d’atténuation ainsi que des matériaux de haute qualité, des
composants sélectionnés, un traitement de première classe et une
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt vpa 4120 velocity bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt vpa 4120 velocity in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds, Noors als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info